Temperature is known as one of the abiotic factors that can affect mold growth. Many mold growth prediction models consider temperature as one of the parameters that can significantly impact mold growth indoors, and hence temperature has been targeted by different indoor mold prevention strategies on different premises. For example, European guidelines for libraries suggest a temperature of 19 °C to preserve books. However, running low temperature air-conditioning (AC) costs substantially more energy, and thus a higher temperature (e.g., 25.5 °C) has been regularly proposed as the recommended indoor temperature for general indoor environments in Hong Kong. It is, therefore, needed to understand whether or not the reduction of indoor temperature would lead to better effectiveness of mold prevention. Using Cladosporium cladosporioides (C. cladosporioides) as the model, its germinating spores were challenged in C. cladosporioides to wet-dry cycles with different combinations of relative humidity (RH, 40%, 60% and 80%) and temperature (19 °C and 28 °C) levels. The survival, lipid peroxidation and catalase (CAT) activity of the treated spores were monitored and compared. C. cladosporioides spores showed similar levels of viability, lipid peroxidation and CAT activity when they were exposed to 19 °C and 28 °C at the same RH, but substantially lower survival and higher oxidative stress were observed under the wet-dry cycles with 40% RH dry periods compared with 60% and 80% RH at both temperatures, suggesting that indoor temperature does not tend to affect the resistance of C. cladosporioides to wet-dry cycles as significantly as the RH level of the dry period. Collectively, this study suggests a more important role for moisture over temperature in indoor mold prevention. The outcome of this study may facilitate the sustainable management of indoor mold problems in buildings.
Indoor mold grows ubiquitously in humid areas and can affect occupants’ health. To prevent indoor mold contamination, one of the key measures suggested by the World Health Organisation and United States Environmental Protection Agency is to maintain an indoor relative humidity (RH) level below 75% or at 30–60%, respectively. However, in tropical and subtropical areas, maintaining these suggested RH levels is equivalent to operating a 24-h air-conditioner (AC) or dehumidifier, which is energy-consuming. As a large part of building expense, the operation time of ACs has been regularly proposed to be cut down because of the requirement of building sustainability. This leads to a trade-off between sustainable building performance and indoor mold hygiene. To balance this trade-off, more sustainable alternatives, such as those that target physical environments (e.g. nutrient and temperature level) or apply new surface coating technologies to inhibit mold growth, have been launched. Despite these initiatives, indoor mold contamination remains an unresolved issue, mainly because these alternative measures only exhibit limited effectiveness or require extra effort. This review aims to summarize the currently adopted mold control measures and discuss their limitations as well as the direction for the future development of sustainable mold control strategies. Significance and Impact of the Study: People spend most of their time indoors and hence the presence of indoor mold contamination can compromise the occupants’ health. With the wake of climate change which is expected to see an increase in RH and temperature, tropical and subtropical areas are even more prone to mold contamination than they used to be. This study may help facilitate the development of sustainable and effective mold control strategies in the indoor environment.
Environmental sustainability is one of the key issues in building management. In Hong Kong, one of the initiatives is to reduce the operation hours of air-conditioning in buildings to cut down energy consumption. In this study, we reported a mold contamination case in a newly refurbished laboratory, in which the air-conditioner was switched from 24- to 18-h mode after refurbishment. In order to prevent mold recurrence, the air-conditioner was switched back to 24-h mode in the laboratory. During the mold investigation, visible mold patches in the laboratory were searched and then cultured, counted and identified. Building and environmental conditions were recorded, and used to deduce different causes of mold contamination. Eight contaminated sites including a wall, a bench, some metal and plastic surfaces and seven types of molds including two Cladosporium spp., two Aspergillus spp., one Rhizopus sp., one Trichoderma sp., and one Tritirachium sp. were identified. Cladosporium spp. were the most abundant and frequently found molds in the laboratory. The contaminated areas could have one to five different species on them. Based on the mold and environmental conditions, several scenarios causing the mold contamination were deduced, and different mold control measures were discussed to compare them with the current solution of using 24-h air-conditioning to control mold growth. This study highlights the importance of mold hygiene in sustainable building management.