The manufacturing process in thermoset-based carbon fiber-reinforced polymers (CFRPs) usually requires a curing stage where the material is transformed from a gel state to a monolithic solid state. During the curing process, micro-residual stresses are developed in the material due to the different chemical–thermal–mechanical properties of the fiber and of the polymer, reducing the mechanical performance of the composite material compared to the nominal performance. In this study, computational micromechanics is used to analyze the micro-residual stresses development and to predict its influence on the mechanical performance of a pre-impregnated unidirectional CFRP made of T700-fibers and an aeronautical grade epoxy. The numerical model of a representative volume element (RVE) was developed in the commercial software Abaqus® and user-subroutines are used to simulate the thermo-curing process coupled with the mechanical constitutive model. Experimental characterization of the bulk resin properties and curing behavior was made to setup the models. The higher micro-residual stresses occur at the thinner fiber gaps, acting as triggers to failure propagation during mechanical loading. These micro-residual stresses achieve peak values above the yield stress of the resin 55 MPa, but without achieving damage. These micro-residual stresses reduce the transverse strength by at least 10%, while the elastic properties remain almost unaffected. The numerical results of the effective properties show a good agreement with the macro-scale experimentally measured properties at coupon level, including transverse tensile, longitudinal shear and transverse shear moduli and strengths, and minor in-plane and transverse Poisson’s ratios. A sensitivity analysis was performed on the thermal expansion coefficient, chemical shrinkage, resin elastic modulus and cure temperature. All these parameters change the micro-residual stress levels and reduce the strength properties.
28 November 2023 in International Journal of Mechanical Sciences
Topology optimization has evidenced its capacity to provide new optimal designs in many different disciplines. However, most novel methods are difficult to apply in commercial software, limiting their use in the academic field and hindering their application in the industry. This article presents a new open methodology for solving geometrically complex non-self-adjoint topology optimization problems, including stress-constrained and stress minimization formulations, using validated FEM commercial software. The methodology was validated by comparing the sensitivity analysis with the results obtained through finite differences and solving two benchmark problems with the following optimizers: Optimality Criteria, Method of Moving Asymptotes, Sequential Least-Squares Quadratic Programming (SLSQP), and Trust-constr optimization algorithms. The SLSQP and Trust-constr optimization algorithms obtained better results in stress-minimization problem statements than the methodology available in ABAQUS®. A Python implementation of this methodology is proposed, working in conjunction with the commercial software ABAQUS® 2023 to allow a straightforward application to new problems while benefiting from a graphic user interface and validated finite element solver.
13 November 2023 in International Journal of Solids and Structures
This work presents detailed 3D modelling and simulation of the mechanical effects induced by lightning strikes in protected carbon fibre-reinforced polymer laminates. Firstly, physically based models that represent the mechanical overpressure that results from a lightning strike are revisited. In particular, this paper compares the implementation of an analytical strong shock wave approximation with the solutions obtained from computational fluid dynamics (CFD), considering different equations of state, to represent the supersonic expansion of the hot plasma channel when simulating the mechanical damage induced by lightning strikes. The assessment of the pressure profiles, the numerical predictions of the displacement and velocity fields and the analysis of the predicted damage maps show that, for two lightning protection layers, the effects of the supersonic plasma expansion loads obtained from the strong shock wave approximation compare reasonably well with those obtained from CFD, independently of the equation of state solved numerically. Subsequently, the predictions of the 3D modelling strategy of the mechanical response of composite laminates subjected to lightning strike employing the strong shock wave approximation are compared with mechanical deformation measurements obtained from lab-scale lightning test results. Accurate deflection and out-of-plane velocity fields are predicted, validating the 3D modelling strategy. Moreover, the predicted damage maps correlate well with the (bulk) damage identified by C-scan (considering only the damaged area below the second ply).
Linerless composite pressure vessels, or type V pressure vessels, are gaining increased interest in the transportation industry because they offer improved storage volume and dry weight, especially for low-pressure cryogenic storage. Nevertheless, the design and manufacturing of this type of pressure vessel bring several challenges due to the inherent difficulties in the manufacturing process implementation, assembly, and related analysis of structural integrity due to the severe operating conditions at cryogenic temperatures that should be taken into consideration. In this work, a novel analysis procedure using a finite element model is developed to perform an end-to-end simulation of a linerless pressure vessel, including the relevant features associated with automated fiber placement manufacturing processes regarding thickness and tape profiles, followed by an analysis of the structural response under service conditions. The results show that residual stresses from manufacturing achieve values near 50% of the composite ply transverse strength, which reduces the effective ply transverse load carrying capacity for pressure loading. Transverse damage is triggered and propagated across the vessel thickness before fiber breakage, indicating potential failure by leakage, which was confirmed by hydrostatic tests in the physical prototype at 26 bar. The cryogenic condition analysis revealed that the thermal stresses trigger transverse damage before pressure loading, reducing the estimated leak pressure by 40%. These results highlight the importance of considering the residual stresses that arise from the manufacturing process and the thermal stresses generated during cooling to cryogenic conditions, demonstrating the relevance of the presented methodology for designing linerless cryogenic composite pressure vessels.