This study explores the design steps of a building foundation in liquefiable soils according to TBDY 2018. For this purpose, geotechnical engineering design was performed in stages including the liquefaction and soil-pile-structure interaction analyses. The problematic issues such as the determination of M-w values that were used during liquefaction analyses, the search for time histories records to be scaled, the absence of recommended tolerable limits for the foundation soil settlements and different assumptions underlying the kinematic and inertial interaction approaches for Method III were addressed.
Pile foundations in earthquake-prone regions must be analyzed and designed considering the dynamic loads. In the fully nonlinear dynamic analyses, the soil nonlinearity can be considered using the modulus degradation curves in the total-stress approach, and the soil damping is controlled by the unloading/reloading rule. Several researchers have investigated the effect of soil damping on the free-field soil response analyses, but the effect on the soil–pile–structure system response has not been studied thoroughly. In this study, the nonlinear elastic method (hyperbolic model) and the elastoplastic Mohr–Coulomb (MC) models were implemented to investigate the effect of soil damping on the pile and structure response. Dynamic soil–pile–structure interaction analyses were performed by simulating two different centrifuge tests published in the literature, and the analysis results were compared with the centrifuge test results. The analyses with the low-intensity input motions showed that the superstructure accelerations and the bending moments in the single pile were estimated with reasonable accuracy. However, the superstructure accelerations might be underestimated under high-intensity motions, especially in the MC model. Additional analyses were performed under six earthquake records. The constitutive models (MC and hyperbolic) may significantly vary the maximum structural acceleration and pile maximum moments (up to 50%). As a result, the responses of the superstructure and the pile in soil–pile–structure interaction problems are highly dependent on the soil constitutive model that must take the damping into account accurately; in turn, due account must be given to the selection of the constitutive model.
Liquefaction-induced damages related to excess pore water pressure generation in soils and stiffness degradation significantly influence infrastructure and seismic ground response, requiring reliable experimental testing setups and validated numerical models for accurate assessment. This study investigates the free-field liquefaction behavior of saturated sands using the newly proposed ETILam (Enhanced Transparent Impermeable Laminar) soil container under 1 g shaking table conditions. Specimens composed of loose and dense saturated sands overlain by a dry sand layer were prepared and tested under two harmonic motions (0.1 g–2 Hz and 0.2 g–2 Hz), the second motion being two consecutive 6 s excitations. Dynamic response was evaluated through acceleration time histories, shear strains obtained through displacement measurements, excess pore water ratio (ru), response spectra, transfer functions, and Fourier amplitude computations. Fully coupled effective stress analyses were performed in 2D and 3D using calibrated PM4Sand and P2PSand constitutive models. Experimental results showed limited liquefaction for the lower-amplitude motion, whereas the higher-amplitude motion triggered significant shear strains (up to 10%) and ru values approaching 0.8, with depth-dependent dissipation patterns between sequential shakings. Numerical simulations reproduced acceleration amplitudes and general pore-pressure trends, with the 2D model providing closer agreement in both generation and dissipation behavior. The findings validate the ETILam container’s capability to simulate free-field liquefaction response and demonstrate that a well-calibrated 2D approach can reliably capture the essential features of the observed behavior.
Waterschap Hollandsche Delta (WSHD) is the regional authority responsible for dike safety of part of the province of Zuid-Holland. The latest safety assessment identified dike segments that do not meet current safety requirements with respect to static liquefaction. This study investigates a dike section along the Oude Maas near Rotterdam, where site investigations indicate layered sand deposits with potentially contractive (liquefiable) behaviour. Cone penetration test (CPT) data collected along the alignment are processed to screen for susceptibility and to determine the depth and thickness of potentially critical layers. Bathymetric surveys further indicate progressive riverbed erosion at the dike toe, and a representative cross section is selected based on the CPT-derived trends together with local geometry and the observed scour extent. Finite element analyses are then used to quantify the mechanical consequences of toe erosion, modelled as staged soil removal consistent with the measured bathymetric evolution. The results show that scour-induced unloading reduces lateral confinement and leads stress paths toward instability, bringing the stress state close to an instability boundary within the most critical zone.