Newly introduced provisional crowns and fixed dental prostheses (FDP) materials should exhibit good physical and mechanical properties necessary to serve the purpose of their fabrication. The aim of this systematic literature review and meta-analysis is to evaluate the articles comparing the physical and mechanical properties of 3D-printed provisional crown and FDP resin materials with CAD/CAM (Computer-Aided Designing/Computer-Aided Manufacturing) milled and conventional provisional resins. Indexed English literature up to April 2022 was systematically searched for articles using the following electronic databases: MEDLINE-PubMed, Web of Science (core collection), Scopus, and the Cochrane library. This systematic review was structured based on the guidelines given by the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA). The focused PICO/PECO (Participant, Intervention/exposure, Comparison, Outcome) question was: ‘Do 3D-printed (P) provisional crowns and FDPs (I) have similar physical and mechanical properties (O) when compared to CAD/CAM milled and other conventionally fabricated ones (C)’. Out of eight hundred and ninety-six titles, which were recognized after a primary search, twenty-five articles were included in the qualitative analysis, and their quality analysis was performed using the modified CONSORT scale. Due to the heterogeneity of the studies, only twelve articles were included for quantitative analysis. Within the limitations of this study, it can be concluded that 3D-printed provisional crown and FDP resin materials have superior mechanical properties but inferior physical properties compared to CAD/CAM milled and other conventionally fabricated ones. Three-dimensionally printed provisional crowns and FDP materials can be used as an alternative to conventional and CAD/CAM milled long-term provisional materials.

Increasing demands for aesthetically pleasing dental restorations have promoted the use of materials that display superior optical properties. Zirconia-based all-ceramic systems have good optical properties, thus providing the desired esthetics for dental restorations. The altered oral conditions impact the physical properties of these materials. Multiple studies have been conducted to evaluate the effect of aging on the mechanical properties of computerized-aided design and computerized-aided manufacturing (CAD/CAM)-based zirconia; however, there is a scarcity of literature discussing the effect of aging on change in translucency, contrast ratio, and color. Therefore, this research aimed to evaluate the effect of accelerated artificial aging on translucency parameter (TP), contrast ratio (CR), and color of CAD/CAM zirconia at different sintering temperatures. Twenty-eight rectangular-shaped specimens were obtained by CAD/CAM milling of zirconia blank. Sintering of the samples was carried out at four different temperatures 1350 °C, 1400 °C, 1450 °C, and 1500 °C, respectively. Thermocycling of the samples was performed in a thermocycler. TP, CR, and color evaluation of all the samples was done again using a Spectrophotometer. Data acquired were statistically evaluated by one-way ANOVA and Post Hoc test. The highest amount of change in TP was recorded for specimens sintered at 1400 °C (1.86), whereas the least change was attributed to 1350 °C (0.51). The highest change in CR was observed in specimens sintered at 1500 °C (0.0971), and the least change in CR was observed at 1450 °C (0.0086). The highest ΔE values were recorded for 1400 °C against both white (1.86) and black background (2.17), whereas the least change was attributed to 1350 °C against white (0.86) and against a black background (1.41). The changes in TP were significant, but CR did not show any significant change. ΔE values for all the experimental groups were significant, but were below the clinically perceptible range. An increase in sintering temperature increased the translucency.

OBJECTIVES: Gingival retraction using impregnated retraction cords using hemostatic agents like 25% Aluminium Chloride is the most important step in isolation of bonded restorations. These agents are known to hinder the bonding of resin to dentin. The aim of the study was to evaluate the effect of two different cleansing protocols on the bond strength of a self etching adhesive to dentin contaminated with hemostatic agents. METHODS AND MATERIALS: Sixty three 1st premolars extracted for therapeutic reasons were randomly divided into three groups A, B and C of 21 samples each . The mid coronal dentin was exposed in all the samples and an even smear layer was produced using a standard diamond point and sandpaper grit. All the samples were contaminated with 25% Aluminium Chloride hemostatic gel. Group A was decontaminated with only water spray, Group B with water spray and 2 % Chlorhexidine (CHX) and Group C with water spray, 2% Chlorhexidine and 10% EDTA gel. All the samples were bonded using a self etch adhesive and composite resin. The microshear bond strength was assessed using Universal Testing Machin ( UTM). RESULTS AND DISCUSSION: A significant improvement in the microshear bond strength was noted in Group B( Water spray and 2%Chlorhexidine) when compared to the Control group A and Group C. CONCLUSION: Decontamination of dentin with water spray and 2% Chlorhexidine solution significantly improved the bond strength of self etch adhesive restorations.