Hurricanes often devastate trees throughout coastal China; accordingly, developing a method to quantitatively evaluate the changes in tree phenotypic characteristics under continuous strong winds is of great significance for guiding forest cultivation practices and mitigating wind hazards. For this research, we built a lifting steel truss carrying a large forced draft fan near a rubber plantation on Hainan Island, and we aligned three selected small rubber trees in a row in front of the fan (with separation distances from the forced draft fan outlet of approximately 1.3, 3.3, and 5.3 m) to explore the susceptibility of rubber trees to the mechanical loading of hurricane-level winds. By adjusting the power of the forced draft fan, four wind speeds were emitted: 0 m/s, 10.5 m/s, 13.5 m/s, and 17.5 m/s. Meanwhile, point clouds of the three rubber trees under different continuous wind speeds were acquired using two terrestrial laser scanners. Computer algorithms were applied to derive the key parameters of the three rubber trees, namely, the zenith and azimuth angles of each leaf, effective leaf area index (LAI), windward area of each tree, volume of the tree canopy, and trunk tilt angle, from these point clouds under all four wind speeds. The results show that by increasing the wind speed from 0 m/s to 17.5 m/s, the leaf zenith angles of the three rubber trees were unimodally distributed with the peak concentrated at 0°, while the leaf azimuth angles were bimodally distributed with the peaks concentrated at 0° and 360°. The effective LAI values of the three trees increased from 2.97, 4.77, and 3.63 (no wind) to 3.84, 5.9, and 4.29 (wind speed of 17.5 m/s), respectively, due to a decrease in the vertical crown projection area caused by the compression of the tree canopy. We also found that the effective LAI, windward area, and canopy volume of the third rubber tree (the tree farthest from the forced draft fan) varied less than those of the other two trees, reflecting the attenuation of the wind speed by the crowns of the two trees closer to the fan. The experimental results also indicate that the joint use of light detection and ranging (LiDAR) data with computer graphics algorithms to analyse the dynamic changes in tree phenotypic characteristics during the passage of a hurricane is promising, enabling the development of a novel strategy for mitigating wind hazards. The proposed method with the designed device capable of producing an adjustable wind speed also has the potential to study the impacts of wind damage under various forest conditions by further modifying the tree spacing and tree species.

Light detection and ranging (LiDAR) technology has become a mainstream tool for forest surveys, significantly contributing to the improved accuracy of forest inventories. However, the accuracy of the scanned data and tree properties derived using LiDAR technology may differ depending on the occlusion effect, scanning configurations, various scanning patterns, and vegetative characteristics of forest plots. Hence, this paper presents a computer simulation program to build a digital forest plot composed of many tree models constructed based on in situ measurement information and two mobile scanning patterns, i.e., airborne laser scanning (ALS) and ground-based mobile laser scanning (MLS). Through the adjustment of scanning parameters and the velocity of vehicle loading LiDAR sensors, the points scanned using two scanning patterns were compared with the original sampling points, derived from the constructed digital forest plots. The results show that only 2% of sampling points were collected by LiDAR sensors with the fastest vehicle speed (10 m/s) and coarsest scanning angular resolution (horizontal angular resolution 0.16° and vertical angular resolution 1.33°), and approximately 50% of sampling points were collected by LiDAR sensors with slow vehicle velocity (1.25 m/s) and a finer scanning angular resolution (horizontal angular resolution 0.08° and vertical angular resolution 0.33°). Meanwhile, the potential extended application of the proposed computer simulation program as a light model of forest plots was discussed to underpin the creation of the forest digital twin. Three main conclusions are drawn: (1) the collected points from airborne laser scanning (ALS) are higher than those collected from ground-based mobile laser scanning (MLS); (2) reducing the vehicle velocity is more efficient at improving the high density of the point cloud data than by increasing the scanning angular resolution; (3) the lateral extension of crown area increasing the light beams’ receptor area and the clumped leaf dispersion augmenting the light penetration with vertical elongation are the two paramount factors influencing the light transmittance of tree crowns.