Sibel Dikicier

Dr. Sibel Dikicier

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 March 2023 in Annals of Medicine
Verified
Journal Article
Open access
SDSibel Dikicier
Sibel Dikicier
CKCumhur Korkmaz
Cumhur Korkmaz
AAArzu Atay
Arzu Atay
MYMert Dogukan Yilmaz
Mert Dogukan Yilmaz
The coronavirus disease-2019 (COVID-19) pandemic has caused healthcare professionals to face unequal acute workplace stress and burnout. This study aimed to analyze the potential impact of COVID-19...

23 November 2022 in BMC Oral Health
Verified
Journal Article
Open access
PDF file
SDSibel Dikicier
Sibel Dikicier
CKCumhur Korkmaz
Cumhur Korkmaz
AAArzu Atay
Arzu Atay
Background: The roughening of the inner surface of a fixed ceramic restoration is an important factor for the bonding process. The aim of this study is to investigate the effect of combined surface treatments (acid etching, air-abrasion and Er: YAG Laser) on surface roughness of CAD/CAM fabricated zirconia (ZrO2) and lithium-disilicate glass ceramics (LDS).Methods: Sixty ZrO2(Ceramill Zi) and LDS (IPS e.max CAD) specimens, (5 mm in width, 5 mm in length and 1.5 mm in height) were fabricated using CAD/CAM and sintered according to the manufacturer’s instructions. All specimens subjected to three surface treatment combinations; etching with 4% hydrofluoric acide (HF), airborne-particle abrasion with 110-μm alumina (Al2O3) (AP) and Er:YAG laser (Er:YAG) (Group A—HF + AP; Group B—Er:YAG + AP, and Group C—Er:YAG + HF). Perthometer was used to measure the surface roughness of the specimens before and after the tretments.Results: Group A presented the highest Ra (LDS 0.81 ± 0.27 and ZrO20.67 ± 0.21 after treatment) and Group C the lowest (LDS 0.45 ± 0.13 and ZrO20.26 ± 0.07, after treatment). Compared with before treatment, the Ra were significantly different only in Group A both ZrO2and LDS after treatment (p < 0.05). Qualitative SEM images suggested the surface topography of the ZrO2was smoother than the LDS. Less surface changes were observed in the Er:YAG combined procedures than HF + AP.Conclusions: HF + AP was significantly succesful in modifying the ceramic surface. Er:YAG did not sufficiently promote the surface topography, even if combined with any other treatments. Overall, surface tretments on ZrO2not easier than LDS.


20 April 2025 in Current Research in Dental Sciences
Verified
Journal Article
Open access
PDF file
MBMerve Botsalı
Merve Botsalı
SDSibel Dikicier
Sibel Dikicier
HBHüseyin Botsalı
Hüseyin Botsalı
AAArzu Atay
Arzu Atay
Objective: The aim of the study is to evaluate the stress distribution of zirconia-reinforced lithium silicate all-ceramic fixed partial dentures under occlusal loading; in terms of material, restoration, and supporting type. Methods: Six different models were analyzed; tooth-supported anterior crown, tooth-supported posterior crown, tooth-supported 3-unit bridge, implant-supported anterior crown, implant-supported posterior crown and implant-supported 3-unit bridge. Milling and pressable zirconia-reinforced lithium silicate were used in each model. Structural analyses were simulated with finite element analysis under vertical and oblique loading to evaluate the von Mises and minimum principal stresses. Results: Tooth-supported restorations showed lower stress values than implant-supported forms of the same restoration. Stresses were higher and distributed over a larger surface under oblique loading compared to vertical loading. Overall stresses generated on the single crown models were higher than the stresses generated on the bridge models. Implant-supported bridge model under oblique loading shows the highest stress. However both milling and pressable forms of zirconia-reinforced lithium silicate didn’t make a difference on the stress concentration and distribution areas. Conclusion: The stress distribution and mechanical behavior of models was influenced by the type of restoration, direction of the force, and the number of units. However, no significant difference was found between milling and pressable zirconia-reinforced lithium silicate ceramic in terms of the stress values on the restorations.