The paper presents an electromagnetically-controlled shape morphing composite (e-morph) as a new variable stiffness changing actuator for soft robotic applications. The structure is composed of a granular core and an outer shell made of silicon, with channels filled with liquid metal. Under an electromagnetic force, the actuator can change its shape in a controlled way, while the jamming mechanism allows the granules used in the core to maintain the desired shape and change their stiffness at a rate higher than 6. This paper provides a detailed description of the concept, empirical and simulation results of the samples tested. Finally, suggestions are made for initial applications using this actuator.
Jammed granular systems, also known as vacuum packed particles (VPP), have begun to compete with the well commercialized group of smart structures already widely applied in various fields of industry, mainly in civil and mechanical engineering. However, the engineering applications of VPP are far ahead of the mathematical description of the complex mechanical mechanisms observed in these unconventional structures. As their wider commercialization is hindered by this gap, in the paper the authors consider experimental investigations of granular systems, mainly focusing on the mechanical responses that take place under various temperature and strain rate conditions. To capture the nonlinear behavior of jammed granular systems, a constitutive model constituting an extension of the Johnson–Cook model was developed and is presented. green The extended and modified constitutive model for VPP proposed in the paper could be implemented in the future into a commercial Finite Element Analysis code, making it possible to carry out fast and reliable numerical simulations.
Vacuum-packed particle (VPP) systems have been recently used in the development of smart structures due to their ability to actively change material stiffness through the mechanism of granular jamming. By altering the strength of the vacuum pressure applied to the particles, the material can be proportionally and reversibly transitioned from a liquidlike low-stiffness state to a stiff state. The ability to control material stiffness in this way opens up different possibilities for the design of morphing and smart structures by allowing them to soften during deformation to reduce actuation energy requirements and to then stiffen once the desired shape has been achieved to provide a zero-energy holding mechanism. The following research describes two useful models that predict the mechanical response of VPP beams under flexural loading. Firstly, four-point bending tests with digital image correlation strain mapping are performed in order to measure the axial and transverse strains in a bending beam made from vacuum-packed particles. The test results show a nonlinear mechanical response, including a change in beam thickness with deformation, that motivated an analytical model of the structure incorporating a nonlinear material stress model based on the Mohr-Coulomb failure envelope. In addition, finite-element simulations are implemented using a Johnson-Cook model extension to predict the response under loading of three-dimensional beam elements at different vacuum pressure levels. Lastly, the models are compared to the experimental results, indicating good agreement. Both methods are shown to be useful for predicting the variation of stiffness of vacuum-packed particle beams.
25 February 2022 in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
The following discussion concerns the use of innovative smart materials called vacuum-packed particles (VPPs) as active energy absorbers. VPP, also known as a granular jamming system, is a structure composed of granular media contained within an elastomer coating. By changing the vacuum pressure inside the coating, it is possible to control the mechanical properties of the structure. VPPs have many applications, e.g. in medicine, robotics, and vibration damping. No attempts have yet been made to use VPPs to absorb the energy of a collision, although, given their properties, this could very well be an interesting application. In the first part of the paper, the general concept of the absorber is presented. Then a prototype and the empirical tests conducted are precisely described. The middle part of the paper considers the basic properties of VPP and modeling methodology. A proposal for a constitutive equation is presented, and a numerical simulation using LS-Dyna was performed. In the final section, the concept of a smart parking post is presented..
3 April 2025 in Archives of Civil and Mechanical Engineering
The rapid development of research on innovative soft robots has been observed in recent years. Most of these robots are equipped with mechanisms that enable adaptive stiffness changes. Although various physical effects facilitate this capability, one of the most intriguing is undoubtedly the granular jamming phenomenon. Structures based on this effect consist of granules enclosed within an elastomer sleeve, with stiffness controlled by vacuum pressure. This work focuses on investigating the properties of such structures subjected to cyclic loading under different stress states. We conducted a wide range of empirical tests under various loading conditions, including compression, tension, and bending. Based on this research, a constitutive equation was proposed to describe this phenomenon. The model was implemented into commercial finite element (FE) software, and numerical predictions were validated with empirical results. Finally, a new concept for a soft robotic gripper utilizing granular jamming as a stiffening mechanism was proposed and tested.
Based on the analysis of the structures of robots and electronics developed so far, it should be noted that a majority of them need a reservoir for electrical energy storage. Unfortunately, most off-the-shelf devices commercially available nowadays are based on rigid parts that heavily limit the possibilities of incorporating such products into soft robots and wearable electronics. To address these issues, a new type of flexible structure for electrical energy storage, which consists of small battery cells connected by liquid metal paths, was proposed. It can achieve a low value of Young’s modulus (about 0.13 MPa) while maintaining electrochemical stability for large stretches (max. capacity reduction—2%). We proposed an individual layer structure as well as a sandwich structure with a granular core, which by way of granular jamming phenomena can change the stiffness (almost 300%). This article describes the concept and working principle of the proposed flexible electrical energy storage structure, followed by the mechanical and electrical characterization, electrochemical impedance spectroscopy, and galvanostatic battery cell cycling. Scanning electron microscopy and energy-dispersive X-ray spectroscopy were used to characterize the electrodes. The article also includes numerical simulations and potential applications of the studied structure.