Titanium dioxide is an important metal oxide semiconductor (MOSs) used in many electronic applications, the most famous of which are gas sensor applications. This review discusses the techniques used for preparing the TiO2 thin films and the effect of the crystalline phases in which this compound forms, on the gas sensing properties. There are three phases to crystallize titanium dioxides, brookite, anatase, and rutile phase. Amongst these varied phases of crystal, the greatest steady main phase is rutile. The phase of anatase and brookite are usually more stable than the rutile phase as the surface energy of them is less than that of the rutile. Therefore, the applications of sensing by anatase TiO2 and rutile TiO2 were fully studied. TiO2 characterizations were established on surface reactions using oxidizing or reducing gases, which; therefore, influences the conductivity of the film. Titanium dioxide gas sensors have healthier steadiness and sensitivity at high temperature compared with that of the other metal oxides. Surveys on titanium dioxide thin film applied in gas sensor devices used in a varied range of applications such as sensor devices, dye-sensitized solar cells, and catalysis. The gas sensor is a function of the crystal structure, particle size, morphology, and the method of synthesis. In this work, characteristic of the titanium dioxide films investigated using various techniques, as reported by many researchers. The aim of this study was to review previous studies through which the best properties can obtained to manufacture TiO2 gas sensor thin films with high sensitivity.
One of the most important n-type semiconductor materials used for large numbers of optoelectronics applications is Zinc Oxide (ZnO). In this paper, an aluminum doped zinc oxide thin films have been prepared using spray pyrolysis technique over a 100 silicon based substrates. Morphological, structural, optical and electrical properties of the prepared thin films were characterized and intensively studied. Different aluminum contents of 1-5% have been utilized to synthesis ZnO nanostructures. The X-ray diffraction method showed that films are crystalline in their structure with hexagonal quartzite phase. Further, FE-SEM methods approved a homogeneous surface morphology with emerging tiny particles as a result of increasing the aluminum concentration. The photoluminescence technique has been used to clarify films optical properties. A clear shift in energy band-gap from 3.26eV to 3.23% has been resulted due to the increasing the Al concentration from 0% to 5%, respectively.
1 September 2013 in International Letters of Chemistry, Physics and Astronomy
ZnO thin films with Cd/Zn nominal ratios of 0%, 1%, 3%, 5%, and 7% and thickness of 0.7 μm were prepared by chemical spray pyrolysis. X-ray diffraction patterns showed that the films have polycrystalline structures and peaks matching the hexagonal ZnO structure. Crystallite sizes ranged from about 35 nm to 87 nm. As the doping concentration increased, full width at half maximum values decreased and crystallite sizes increased. The UV-Vis spectra of the ZnO:Cd films showed high transparency in the visible region. The optical band gap of the ZnO:Cd films decreased from 3.255 eV to 3.17 eV with increasing Cd doping concentration. The transition type was direct, thereby allowing transition. The ZnO:Cd thin films were annealed at 400 °C, and annealing treatment showed improvements in the properties of the derived films.
Nickel-doped Tin dioxide (NSO) nanostructured thin films were deposited using chemical spray pyrolysis at 450 °C at various spray rates. The structural, morphological, and optical properties of the prepared nanostructured thin films were investigated to determine the effect of these parameters on the sensing properties of NSO film. X-ray diffraction revealed a polycrystalline structure with an increasing crystallite size as the deposition rate increased, which resulted in a gradual decrease in the bandgap. The FE-SEM images demonstrate that the deposition rate significantly influences the surface morphology and gas sensitivity performance. The sensitivity of the NO 2 gas sensor fabricated employing NSO thin films increased as the deposition rate, and NO 2 concentration was increased. At an optimal sensing temperature of 373 K, the maximum sensitivity was 120%, with a response and recovery time of 17 and 19 s, respectively.
4 April 2022 in Journal of Materials Science: Materials in Electronics