The disposal and utilization of solid waste of coal gangue is one of the main problems in coal mining in China. Injecting coal gangue into goaf in the form of slurry can effectively solve the problems of ground stacking and environmental pollution prevention. In order to obtain the flow law of gangue slurry in the void of the accumulated rock in the goaf, a visualization simulation test device for gangue slurry permeation grouting in the goaf was independently designed. The flow and diffusion characteristics, flow and diffusion velocity changes, void pressure changes, and viscosity changes of three mass concentrations (76%, 78%, 80%) of gangue slurry in the void between caved rock blocks in goaf were studied by visual grouting simulation test. The results show that: (1) The seepage process of gangue slurry in the goaf simulation test is divided into three diffusion forms, namely radial diffusion, axial diffusion, and bidirectional diffusion. The three diffusion forms are interrelated and inseparable. (2) The initial flow velocity of the slurry with different concentrations is different under the same permeation grouting pressure, and the higher the slurry concentration, the smaller the initial flow velocity of the slurry. The velocity of the slurry has a nonlinear relationship with the diffusion distance of the slurry. (3) With the permeation and diffusion of slurry, pressure sensors at different positions are subjected to pressure from bottom to top and enter the pressure boost stage, gradually forming stress peaks. When the slurry exceeds the position of the pressure sensor, the pressure on the pressure sensor is weakened and begins to enter the pressure relief stage, and the stress decline trend gradually becomes gentle with time. (4) The water loss effect occurs during slurry flow interaction with rock mass, resulting in slurry viscosity increasing. The viscosity of the slurry affects the difference in the amount of viscosity change. The research results can provide a certain theoretical basis for the goaf gangue slurry filling project.
Upper protective seam mining has been widely applied in China, but the theory of long-distance multiple upper protective seam mining is not yet perfect. In order to investigate the overburden stress evolution law of repetitive mining of long-distance coal seam groups, an experimental study was conducted to simulate similar materials under repeated mining conditions in the long-distance double upper protective layer in the background of Pingmei Group 8th coal mine. By analyzing the roof-collapse structure and the stress evolution law of different layers of the floor during the superposition mining, the pressure-relief range of the protective layer after the mining of the double upper protective layer was determined. The study results showed that: the pressure relief of the protective layer in the long-distance upper protective layer mining was a dynamic process. After the mining of Group D coal seam, the maximum impact depth of the bottom plate could reach 182 m, and the pressure-relief angle of the upper side of Group E coal seam was 65°, and the pressure-relief angle of the lower side was 75°. The distance behind the vertical projection of the working face of Group D was 42 m. The overlapping back mining would affect the stress distribution of Group F coal seam. The pressure-relief angle of the upper side of Group F coal seam was 88°, and the pressure-relief angle of the lower side was greater than 78°. The distance behind the vertical projection of the working face of Group E was less than 61 m. The superposition and staggered mining of double protective layers could expand the protective layer. Through the verification of the measurement of gas parameters on site, it can be seen from the results that it has a certain protection effect. The research results can enrich the theory of long-distance multiple upper protective layer mining, and provide theoretical guidance for long-distance Coal Seam Group Mining in Pingmei coal-mine area.
For extra-thick coal seams, slice mining is a safer mining method than top coal mining, which can effectively reduce the strong mine pressure behavior caused by mining. However, in the slice mining of high-gas and extra-thick coal seams, the gas in the lower slice flows into the goaf, which increases the gas control difficulty on the upper slice working face. It is easy to cause the gas transfinite at the upper corner in the upper slice and reduce the mining efficiency. Therefore, it is of a great significance to carry out the research on gas control technology in slice mining of the extra-thick coal seam. There are some problems in the gas control of slice mining, such as a single gas control method, low control efficiency, and unclear gas migration law. Therefore, it is necessary to study the gas migration law and propose a targeted prevention and control the technical scheme. In order to improve the gas control efficiency of the extra-thick coal seam, the evolution law of permeability of the lower slice is obtained under mining through experimental research. The liquid-solid coupling seepage-flow model for gas migration is established in the lower slice. Comsol Multiphysics software is used to study the migration law of pressure relief gas in the lower slice. Based on the gas migration law, the gas extraction and cut flow technology for the lower slice long borehole is proposed. Through this technology, the amount of gas flowing into the upper slice goaf and the gas content of the lower slice are reduced, and the drilling horizon is optimized. The research results show that the determination of the optimal drilling horizon of the lower slice needs to balance the amount of gas flowing into the goaf and the total amount of gas extraction. The range of 3-7 m horizon in the lower slice is appropriate to the boreholes arranged. When the borehole is located in the lower slice -3 m horizon, the 360 day gas emission quantity of goaf can be reduced to 51.2% of the nondrilled emission quantity, and the total extraction amount is 1143 m3. When the borehole is located in the lower slice -7 m horizon, the 360 day gas emission quantity of goaf can be reduced to 95.31% of the nondrilled emission quantity, and the total extraction amount is 1461 m3. Considering the gas emission capacity of the upper slice and ensuring that the total extraction volume of the lower slice is maximized and the boreholes in the lower slice are not damaged, the boreholes are located in the -6 m horizon of the lower slice.
With the shift of coal resources to deep mining, the occurrence of long‐distance coal seams has increased, and protective layer mining is facing new challenges. This paper attempts to explain the stress evolution law of the upper coal group in the long‐distance mining of the lower coal group in Pingdingshan No. 8 Coal Mine. A simulation model of advance mining of lower‐group coal long‐distance was established. The stress evolution law of the upper coal seam under the influence of advanced mining disturbance of the lower coal seam is studied. The following conclusions were obtained: The advance mining of the lower coal group had a positive or negative impact on the stress distribution of the upper coal seam group. With the recovery of the lower coal group of the F‐21030 working face, the overburden of the F‐21030 goaf finally formed a “Y” type pressure relief area. The pressure relief effect of the E‐21070 working face near the stopping line was obvious. The coal seam of Group E was divided into three areas affected by the advance mining of the lower coal seam. The maximum pressure relief value was 6.6% lower than the initial stress. According to the simulation results, the E‐21070 working face was divided into three regions, namely, the pressure relief region, the stress increase region, and the original stress region. According to the field drainage results of pressure relief gas, the extraction curve could be divided into three parts, namely, the stable area, pressure relief area, and stress recovery area. The maximum pure gas drainage volume could reach seven to eight times of the original area. The pressure relief extraction effect was remarkable, and the optimal extraction range was 22–210 m behind the coal face of the group.
When pressure relief mining of a non‐all‐coal protective layer, to realize the accurate regulation of the pressure relief range and pressure release value of mining height, it is necessary to carry out research on the migration of overburden and the stress distribution law of stope under mining height control. Through similar material simulation experiments, four groups of similar material simulation experimental models were established. The laws of rock strata movement and stress distribution at 2, 4, and 5 m mining heights under different geological conditions, and the laws of rock strata movement and stress distribution at 5 and 8 m mining heights under the same geological conditions were obtained. The research results show that the geological conditions and mining height do not affect the evolution of the rock strata movement range. The highest position of the strata movement and deformation is linearly related to the advancing distance of the coalface. The maximum height of rock strata movement increases abruptly when encountering the key strata, but it still has a linear relationship. The highest position of each expansion of the fracture zone has an exponential relationship with the advancing distance of the coalface. When the key strata are encountered, the maximum height of the fracture zone increases abruptly. The change in mining height only affects the distribution range of the “three zones.” The mining height controls the stress distribution of stope by adjusting the “three zones” of the roof. With the increase in mining height, the caving zone and fracture zone range increase. The corresponding pressure relief range and pressure relief value show the change law of first increasing and then decreasing. There is an optimal mining height, which can make the pressure relief effect of stope best.
Based on the engineering background of coalbed methane block in Liujia District of Fuxin with complex geological conditions, a seepage mathematical model considering the dynamic changes of porosity and permeability of coal reservoir caused by coal matrix shrinkage under the conditions of gas adsorption, desorption, and stress change is established. A geological model of heterogeneous coalbed methane reservoir is established, which includes igneous rock and fault geological structure. The influence of permeability on coalbed methane productivity and reservoir pressure under complex geological conditions is studied by numerical simulation. The results show that the permeability of coal seam is an important factor affecting the yield of coalbed methane. The higher the permeability, the faster the output rate of coalbed methane, the higher the output, the faster the pressure drop of coal reservoir, and the faster the desorption rate of coalbed methane. Under the premise that the horizontal wellbore is perpendicular to the maximum permeability direction of the coal seam, the productivity of the well arrangement method is higher than that of the parallel maximum permeability direction. However, the length of the horizontal well in the Liujia block is limited by the dense igneous rock distribution, and the desorption area of the coalbed methane is reduced and the production is reduced when the vertical arrangement is arranged. Therefore, the horizontal wells in the Liujia block should be parallel to the maximum permeability direction and set along the direction of igneous rock. The greater the vertical permeability of the coal seam, the faster the reservoir pressure decreases, and the better the horizontal well productivity.