Sergey Rushchits

Sergey Rushchits


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
Radionova LiudmilaRadionova Liudmila
Radionova Liudmila
DPDanil V. Perevozchikov
Danil V. Perevozchikov
AMAleksandr N. Makoveckii
Aleksandr N. Makoveckii
VEVictor N. Eremin
Victor N. Eremin
AAAlexander M. Akhmedyanov
Alexander M. Akhmedyanov
SRSergey Rushchits
Sergey Rushchits
In this study, the hot deformation behavior of austenitic Ti-modified AISI 321 steel with a relatively high content of carbon (0.07 wt.%) and titanium (0.50 wt.%) was studied in the temperature range of 1000–1280 °C and strain rates in the range of 0.01–1 s−1. Hot deformation was carried out with uniaxial compression of cylindrical specimens on a Gleeble 3800 thermomechanical simulator. It is shown that the flow stress increased with a decrease in the deformation temperature and an increase in the strain rate. The shape of the stress-strain curves indicates that, at high temperatures and low strain rates, the hot deformation of AISI 321 steel was accompanied by dynamic recrystallization. The passage of dynamic recrystallization was confirmed by microstructural studies. Hyperbolic sine type of constitutive equation with deformation activation energy Q = 444.2 kJ·mol−1 was established by analyzing the experimental flow stresses. The power-law dependences of the critical strain necessary for the onset of dynamic recrystallization and the size of recrystallized grains on the Zener–Hollomon parameter were established. The value of the parameter Z = 5.6 × 1015 was determined, above which the dynamic recrystallization was abruptly suppressed in the steel under study. It is speculated that the suppression of dynamic recrystallization occurs due to dispersed precipitates of titanium carbonitrides.

8 August 2023 in Metals
Verified
Journal Article
Open access
PDF file
Radionova LiudmilaRadionova Liudmila
Radionova Liudmila
DPDanil V. Perevozchikov
Danil V. Perevozchikov
AMAleksandr N. Makoveckii
Aleksandr N. Makoveckii
VEVictor N. Eremin
Victor N. Eremin
AAAlexander M. Akhmedyanov
Alexander M. Akhmedyanov
SRSergey Rushchits
Sergey Rushchits
The kinetics of austenite grain growth during thermomechanical treatment of AISI 321 steel with a relatively high content of carbon (0.07 wt. %) and titanium (0.50 wt. %) were studied. Hot deformation was carried out by the uniaxial compression of cylindrical specimens on a Gleeble 3800 thermomechanical simulator. A dependence is obtained for calculating the kinetics of austenite grain growth for a temperature range of 1150–1250 °C. The proposed dependence makes it possible to evaluate grain growth under non-isothermal conditions. The verification of the adequacy of the proposed dependence and the method for calculating the grain size at cooling rates 0.2, 1 and 5 °C/s showed its high convergence. The difference between the calculated and experimental grain size did not exceed 8%. The suppression of grain growth is due to the precipitation of titanium carbides and carbonitrides. Using the developed grain growth model, an analysis was made of the reasons for the formation of large grains in the shell after the elongating in the production process.

1 January 2018 in Bulletin of the South Ural State University. Series ‘Metallurgy’
Verified
Journal Article
Open access
PDF file
SUSouth Ural State University
South Ural State University
SRSergey Rushchits
Sergey Rushchits
AAA. Akhmedianov
A. Akhmedianov
AMA. Makovetskiy
A. Makovetskiy
АКА. О. Красноталов
А. О. Красноталов
АМА. Н. Маковецкий
А. Н. Маковецкий
ЗАКАЛКА С ПОСЛЕДУЮЩИМ ОБОГАЩЕНИЕМ УГЛЕРОДОМ НЕПРЕВРАЩЕННОГО АУСТЕНИТА (Q&P ОБРАБОТКА) МАРТЕНСИТНОЙ КОРРОЗИОННОСТОЙКОЙ СТАЛИ AISI 414

1 December 2023 in Russian Metallurgy (Metally)
Verified
Journal Article
Closed access
PDF file
SRSergey Rushchits
Sergey Rushchits
Nataliya ShaburovaNataliya Shaburova
Nataliya Shaburova
VSV. V. Sedukhin
V. V. Sedukhin
AAA. M. Akhmed’YAnov
A. M. Akhmed’YAnov
SSS. P. Samoilov
S. P. Samoilov
ICI. V. Chumanov
I. V. Chumanov
The deformation behavior of cast super duplex steel is studied in the temperature range 1100–1250°C and the strain rate range 0.1–10 s–1. Hot deformation is performed by uniaxial compression of cylindrical specimens on a Gleeble 3800 simulator of thermomechanical processes. The flow stresses are shown to decrease with increasing temperature and decreasing strain rate in accordance with a change in the Zener–Hollomon parameter of the temperature–rate deformation conditions. The shape of the flow curves indicates that hot deformation is accompanied by intense dynamic softening, as a result of which the flow stresses decrease or remain unchanged after reaching peak values. Under all hot deformation conditions, ferrite acquires a dynamically recrystallized structure. At the lowest deformation temperature (1100°C) and relatively high strain rates (1–10 s–1), the mechanism of austenite softening is dynamic recovery. A decrease in the strain rate or an increase in the deformation temperature causes partial dynamic recrystallization of austenite. Under similar deformation conditions, the plastic flow stress of the steel under study is significantly higher than that in standard duplex stainless steels. When analyzing the peak flow stresses, we determined the effective hot deformation activation energy (Q = 501.31 kJ/mol) required for calculating the Zener–Hollomon parameter. An expression for describing the peak flow stress is obtained in the form of a hyperbolic function of the Zener–Hollomon parameter. This expression describes the experimental data array with a high accuracy and can be used to estimate the required energy–force parameters of forging and rolling equipment. A comparative estimation of the hot ductility of the super duplex steel is performed by finding the strain corresponding to the appearance of the first macrocracks on the specimen surface. At a strain rate of 10 s–1 (which is characteristic of hot forging processes), the safest deformation temperature range of the steel is shown to be 1150–1250°C, in which austenite undergoes partial dynamic recrystallization reducing the risks of cracking.

1 January 2018 in Bulletin of the South Ural State University. Series ‘Metallurgy’
Verified
Journal Article
Open access
PDF file
SUSouth Ural State University
South Ural State University
Nataliya ShaburovaNataliya Shaburova
Nataliya Shaburova
МКМ. С. Киштыкова
М. С. Киштыкова
VGV. Goldstein
V. Goldstein
SRSergey Rushchits
Sergey Rushchits
СРС. В. Рущиц
С. В. Рущиц
ИССЛЕДОВАНИЕ ДЕФЕКТОВ ГОРЯЧЕКАТАНОГО ЛИСТА ИЗ ТРУБНОЙ СТАЛИ И ПРИЧИН ИХ ОБРАЗОВАНИЯ

1 January 2016 in Bulletin of the South Ural State University. Series ‘Metallurgy’
Verified
Journal Article
Open access
SRSergey Rushchits
Sergey Rushchits
AAA Akhmed'Yanov
A Akhmed'Yanov
Mikhail SmirnovMikhail Smirnov
Mikhail Smirnov
ILI Lapina
I Lapina
VGV Gol'Dshteyn
V Gol'Dshteyn