Electric vehicles (EVs) are being endorsed as the uppermost successor to fuel-powered cars, with timetables for banning the sale of petrol-fueled vehicles announced in many countries. However, the range and charging times of EVs are still considerable concerns. Fast charging could be a solution to consumers’ range anxiety and the acceptance of EVs. Nevertheless, it is a complicated and systematized challenge to realize the fast charging of EVs because it includes the coordinated development of battery cells, including electrode materials, EV battery power systems, charging piles, electric grids, etc. This paper aims to serve as an analysis for the development of fast-charging technology, with a discussion of the current situation, constraints and development direction of EV fast-charging technologies from the macroscale and microscale perspectives of fast-charging challenges. If the problem of fast-charging can be solved, it will satisfy consumers’ demand for 10-min charging and accelerate the development of electric vehicles. This paper summarized the development statuses, issues, and trends of the macro battery technology and micro battery technology. It is emphasized that to essentially solve the problem of fast charging, the development of new battery materials, especially anode materials with improved lithium ion diffusion coefficients, is the key. Finally, it is highlighted that red phosphorus is one of the most promising anodes that can simultaneously satisfy the double standards of high-energy density and fast-charging performance to a maximum degree.
The lifetime of Li-ion batteries (LIBs) is highly dependent on the imperceptible physical/chemical changes/reactions that occur on/between the electrodes and electrolyte. Therefore, reliable and repeatable high-precision detection of the imperceptible changes/reactions is extremely significant. High precision electrochemical measurements, such as high-precision coulombic efficiency, isothermal heat flow, and leakage current, can indicate imperceptible parasitic reaction and predict the practical working status of batteries and the battery life. However, the exact imperceptible physical/chemical changes/reactions inside the battery and battery damage remain unknown. Thus, high-precision material characterization techniques, such as in situ synchrotron radiation techniques in particular, which can demonstrate the structural evolution of materials dynamically during battery working are much needed. High-precision electrochemical measurements and material measurements are used to compare the two departments of a “battery hospital” metaphorically, and combining these two “diagnoses” is the best “consultation” for the battery. This paper is the first to present high-precision measurements from both levels of electrochemical science and materials science of LIBs. The aim of this work is to offer detailed and timely insight into the application of high-precision measurements for battery performance and material analysis, thus benefitting and promoting the further development of LIBs/battery systems.
To solve the problems of fast‐charging of lithium‐ion batteries in essence, development of new electrode materials with higher lithium‐ion diffusion coefficients is the key. In this work, a novel flower‐like Ni@SnNi structure is synthesized via a two‐step process design, which consists of the fabrication of Ni cores by spray pyrolysis followed by the formation of SnNi shells via a simple oxidation–reduction reaction. The obtained Ni@SnNi composite exhibits an initial capacity of ≈693 mA h g−1 and a reversible capacity of ≈570 mA h g−1 after 300 charge/discharge cycles at 0.5 C, and maintains 450 mA h g−1 even at a high rate of 3 C. Further, it is proved that a Ni@SnNi composite possesses high lithium‐ion diffusion coefficient (≈10−8), which is much higher than those (≈10−10) reported previously, which can be mainly attributed to the unique flower‐like Ni@SnNi structure. In addition, the full cell performance (Ni@SnNi‐9h/graphite vs LiCoO2) with a capacity ratio of 1.13 (anode/cathode) is also tested. It is found that even at 2 C rate charging/discharging, the capacity retention at 100 cycles is still close to 89%. It means that Ni@SnNi‐9h is a promising anode additive for lithium‐ion batteries with high energy density and power density.
1 December 2022 in Journal of the Electrochemical Society
The growing interest in wearable electronics has triggered an enormous demand for flexible/wearable power sources. Flexible batteries, including lithium-ion batteries, Sodium-ion batteries, and Zinc/Zinc-Air batteries have been developed greatly. Nanofiber nonwoven fabrics form highly porous networks with remarkable interconnectivity between their pores, making them play an important role in flexible batteries as separators, current collectors, electrodes, etc. It looks that nanofiber nonwoven fabrics are promising to apply in flexible batteries, thus it is time to summarize their fabrication technology, flexible characteristics, electrochemical performance, and application prospects. This review paper focused on the current application status, emerging developments, and challenges of nanofiber nonwoven fabrics produced by electrospinning on flexible batteries. It is hopeful that this job will provide important references for the flexible batteries industrialization.
The rapid growth of renewable energy sources and the expanding market for electric vehicles (EVs) have escalated the demand for safe lithium-ion batteries (LIBs) with excellent performance. But the limitations of safety issues and energy density for LIBs continue to be obstacles to their future use. Recently, single-ion covalent-organic-framework-based (COF-based) solid electrolytes have emerged as a promising avenue to address the limitations of traditional liquid electrolytes and enhance the performance of LIBs. COFs have a porous structure and abundant electron-donating groups, enabling the construction of an available ionic conductive network. So, COFs are the subject of extensive and in-depth investigation, especially in terms of the impacts their adjustable porous structure and tunable chemistry on the research of ionic transport thermodynamics and transport kinetics. In this perspective, we present a comprehensive and significant overview of the recent development progress of single-ion COF-based solid electrolytes, highlighting their rare performance and potential applications in solid lithium batteries. This review illustrates the merits of single-ion conducting solid electrolytes and single-ion COF conductor-based solid electrolytes. Furthermore, the properties of anionic, cationic, and hybrid single-ion COF-based conducting electrolytes are discussed, and their electrochemical performance is also compared when applied in Li-ion batteries. Finally, to solve challenges in COF-based Li-ion batteries, strategies are provided to obtain a high lifespan, rate performance, and stable and safe batteries. This work is promising to offer valuable insights for researchers and the energy storage industry.