Sound wave is an extensively existing mechanical wave, especially in marine and industrial plants where low-frequency acoustic waves are ubiquitous. The effective collection and utilization of sound waves provide a fresh new approach to supply power for the distributed nodes of the rapidly developing Internet of Things technology. In this paper, a novel acoustic triboelectric nanogenerator (QWR-TENG) was proposed for efficient low-frequency acoustic energy harvesting. QWR-TENG consisted of a quarter-wavelength resonant tube, a uniformly perforated aluminum film, an FEP membrane, and a conductive carbon nanotube coating. Simulation and experimental studies showed that QWR-TENG has two resonance peaks in the low-frequency range, which effectively extends the response bandwidth of acoustic–electrical conversion. The structural optimized QWR-TENG has excellent electrical output performance, and the maximum output voltage, short-circuit current and transferred charge are 255 V, 67 μA, and 153 nC, respectively, under the acoustic frequency of 90 Hz and sound pressure level of 100 dB. On this basis, a conical energy concentrator was introduced to the entrance of the acoustic tube, and a composite quarter-wavelength resonator-based triboelectric nanogenerator (CQWR-TENG) was designed to further enhance the electrical output. Results showed that the maximum output power and the power density per unit pressure of CQWR-TENG reached 13.47 mW and 2.27 WPa⁻¹m⁻², respectively. Application demonstrations indicated that QWR/CQWR-TENG has good capacitor charging performance and is expected to realize power supply for distributed sensor nodes and other small electrical devices.

Vibration sensing is of great significance in offshore engineering monitoring and safety detection. This paper presented a low-frequency vibration sensor (LV-TENG) based on a cantilever-beam-structured triboelectric nanogenerator, which can perform high-precision vibration sensing while conducting vibration energy collection effectively. The LV-TENG was composed of two aluminum electrode layers, a spring steel sheet covered with polytetrafluoroethylene (PTFE) and a first-order vibration mode structured frame. Under the excitation of external vibration, the spring steel sheet undergoes first-order modal vibrations between the aluminum electrodes and generates a periodically fluctuating electrical signal in the external circuit. The vibration profile of the cantilever beam was first analyzed theoretically to provide guidance for structural design. On this basis, the influence of the main structural parameters, including the structure of the Al electrode, the thickness of the steel plate, and the electronegative materials, on the output performance of LV-TENG was experimentally investigated and the structure was optimized to enhance electrical output. The results showed that the LV-TENG can accurately sense structure vibration with a frequency of 0.1 Hz to 5.0 Hz and an amplitude of 2.0 mm to 10.0 mm. The measured output voltage followed a positive linear relationship with frequency and the fitted correlation coefficient reached 0.994. The demonstration experiment indicated that the LV-TENG is expected to provide a new avenue for low-frequency vibration monitoring and can be used for structural health monitoring analysis in marine engineering.

Measurement While Drilling (MWD) is the most commonly used real-time information acquisition technique in offshore intelligent drilling, its power supply has always been a concern. Triboelectric nanogenerators have been shown to harvest low-frequency vibrational energy in the environment and convert it into electricity to power small sensors and electrical devices. This work proposed a cantilever-beam-based triboelectric nanogenerator (CB-TENG) for transverse vibration energy harvesting of a drill pipe. The CB-TENG consists of two vibrators composed of spring steel with PTFE attached and Al electrodes. The structurally optimized CB-TENG can output a peak power of 2.56 mW under the vibration condition of f = 3.0 Hz and A = 50 mm, and the electrical output can be further enhanced with the increased vibration parameters. An array-type vibration energy harvester integrated with eight CB-TENGs is designed to fully adapt to the interior of the drill pipe and improve output performance. The device can realize omnidirectional vibration energy harvesting in the two-dimensional plane with good robustness. Under the typical vibration condition, the short-circuit current and the peak power can reach 49.85 μA and 30.95 mW, respectively. Finally, a series of demonstration experiments have been carried out, indicating the application prospects of the device.

As electronic components progressively downsize and their power intensifies, thermal management has emerged as a paramount challenge. This study presents a novel, high-efficiency finned heat exchanger, termed Flat-Plate Oscillating Heat Pipe Finned Radiator (FOHPFR), which employs arrayed flat-plate oscillating heat pipes (OHP) as heat dissipation fins. Three-dimensional (3D)-printed techniques allow the internal microchannels of the FOHPFR to become rougher, providing excellent surface wettability and capillary forces, which in turn significantly improves the device’s ability to dissipate heat. In this study, the 3D-printed FOHPFR is compared with traditional solid finned radiators made of identical materials and designs. The impacts of filling ratio, inclination angle, and cold-end conditions on the heat transfer performance of the 3D-printed FOHPFR are investigated. It is demonstrated by the results that compared to solid finned radiators, the FOHPFR exhibits superior transient heat absorption and steady-state heat transfer capabilities. When the heating power is set at 140 W, a decrease in thermal resistance from 0.32 °C/W in the solid type to 0.11 °C/W is observed in the FOHPFR, marking a reduction of 65.6%. Similarly, a drop in the average temperature of the heat source from 160 °C in the solid version to 125 °C, a decrease of 21.8%, is noted. An optimal filling ratio of 50% was identified for the vertical 3D-printed FOHPFR, with the minimal thermal resistance achieving 0.11 °C/W. Moreover, the thermal resistance of the 3D-printed FOHPFR is effectively reduced compared to that of the solid finned radiator at all inclination angles. This indicates that the FOHPFR possessed notable adaptability to various working angles.