The transport sector generates a considerable amount of greenhouse gas (GHG) emissions worldwide, especially road transport, which accounts for 95% of the total GHGs. It is commonly known that Electric vehicles (EVs) can significantly reduce GHG emissions. However, with a fossil-fuel-based power generation system, EVs can produce more GHGs and therefore cannot be regarded as purely environmentally friendly. As a result, renewable energy sources (RES) such as photovoltaic (PV) can be integrated into the EV charging infrastructure to improve the sustainability of the transportation system. This paper reviews the state-of-the-art literature on power electronics converter systems, which interface with the utility grid, PV systems, and EVs. Comparisons are made in terms of their topologies, isolation, power and voltage ranges, efficiency, and bi-directional power capability for V2G operation. Specific attention is devoted to bidirectional isolated and non-isolated EV-interfaced converters in non-integrated architectures. A brief description of EV charger types, their power levels, and standards is provided. It is anticipated that the studies and comparisons in this paper would be advantageous as an all-in-one source of information for researchers seeking information related to EV charging infrastructures.

Wireless power transfer (WPT) systems’ efficiency is significantly impacted by non-monotonic variations in the coupling coefficient. For very short distances or strong-coupling cases, the WPT efficiency is minimal at the natural resonant frequency, with two peaks around this frequency, known as the frequency splitting phenomenon. On the other hand, WPT capability decreases for long distances or weak coupling cases. Therefore, adaptive matching is required for WPT systems with varying distances, like wireless charging systems for electric vehicles (EVs). This paper first presents a detailed analysis of the frequency splitting phenomenon by studying the root locations of the WPT system’s transfer function. Then, a real-time fixed-frequency adaptive impedance matching (IM) method is proposed, in which the amplitude and phase of the input impedance is estimated using the average active power, the average reactive power, and the amplitude of input voltage. Unlike traditional search-and-find techniques, the proposed method calculates the optimal IM network parameters only in a single iteration, which improves the convergent speed. A scaled-down 20-Watt prototype controlled by the TMSF2812 is fabricated and used to validate the effectiveness of the proposed method over a wide range of coil-to-coil distances.

The rising Greenhouse Gas (GHG) emissions stemming from the extensive use of automobiles across the globe represent a critical environmental challenge, contributing significantly to phenomena such as global warming and the deterioration of air quality. To address these challenges, there is a critical need for research and development in electric vehicles (EVs) and their associated charging infrastructure, including off-board and on-board chargers (OBCs). This paper aims to bridge the gaps in existing review literature by offering a comprehensive review of both integrated and non-integrated OBCs for EVs, based on the authors’ knowledge at the time of writing. The paper begins by outlining trends in the EV market, including voltage levels, power ratings, and relevant standards. It then provides a detailed analysis of two-level and multi-level power converter topologies, covering AC-DC power factor correction (PFC) and isolated DC-DC topologies. Subsequently, it discusses single-stage and two-stage non-integrated OBC solutions. Additionally, various categories of integrated OBCs (iOBCs) are explored, accompanied by relevant examples. The paper also includes comparison tables containing technical specifications and key characteristics for reference and analysis.

Photovoltaic (PV) plants can be built rapidly when compared with other conventional electrical plants; hence, they are a competent candidate for supplying the electricity grid. The output power of the PV modules can be used in plug-in electric vehicles (PEVs) DC charging stations to reduce the burden on the electricity grid, particularly during peak load hours. To integrate PV modules and electric vehicles (EVs) with the electricity grid, the modular multilevel converters (MMCs) topologies producing staircase voltage waveforms are preferred as they are able to deliver less total harmonic distortion (THD) and higher efficiency in addition to lower voltage stress on semiconductor switches. In conventional centralized MMC topologies, a direct connection to a high-DC-link input voltage is required which is not appropriate for PV plants. A new MMC topology for PV/EV/grid integration is proposed in this paper, where the individual PV arrays are directly connected to each phase of the AC grid to harvest the maximum available power point. A current-source converter (CSC) based on a single-stage isolated SEPIC converter is adopted as the submodule (SM) for the proposed MMC topology given its outstanding features, such as low input ripple current, high efficiency, high power factor, and flexible output voltage higher or lower than the input voltage. The single-stage SMs can operate in both DC/DC and DC/AC operating modes. Proper controllers for each mode of operation are designed and applied to supply constant current from either the PV modules or the battery cells by eliminating the second-order harmonic component. The performance of the proposed converter is verified by simulations and a downscaled prototype controlled by TMSF28335 DSP.

This paper presents operation and control systems for a new modular on-board charger (OBC) based on a SEPIC converter (MSOBC) for electric vehicle (EV) applications. The MSOBC aims to modularise the battery units in the energy storage system of the EV to provide better safety and improved operation. This is mainly achieved by reducing the voltage of the battery packs without sacrificing the performance required by the HV system. The proposed MSOBC is an integrated OBC which can operate the EV during traction and braking, as well as charge the battery units. The MSOBC is composed of several submodules consisting of a full-bridge voltage source converter connected on the ac side and SEPIC converter installed on the battery side. The SEPIC converter controls the battery segments with a continuous current because it has an input inductor which can smooth the battery’s currents without the need for large electrolytic capacitors. The isolated version of the SEPIC converter is employed to enhance the system’s safety by providing galvanic isolation between the batteries and the ac output side. This paper presents the necessary control loops to ensure the optimal operation of the EV with the MSOBC in terms of charge and temperature balance without disturbing the required modes of operation. The mathematical analyses in this paper are validated using a full-scale EV controlled by TMS320F28335 DSP.

In this paper, the frequency splitting phenomenon is precisely investigated based on the concept of the maximum power transfer theorem for a two-coil wireless power transfer (WPT) system. Here, unlike the previous studies, in which the analysis were performed by the reflected impedance, the scrutiny is conducted based on the thevenin equivalent impedance. First, the cause of the frequency splitting phenomenon is described using the frequency characteristics of the thevenin impedance and the load power. Second, the splitting equation is derived and the splitting frequencies are calculated through it. Eventually, some methods, that have been used so far to improve the power transfer capability, in the presence of the frequency splitting phenomenon, are mentioned. In addition, using simulation results by MATLAB software, these methods are compared together and the best method is obtained.