Metal waste recycling has become a global requirement owing to its environmental benefits and powerful economic activity. Metal nail waste (MNW) is a byproduct of metal nail manufacture. MNW has an equal size, contains a high ratio of iron, and has a high specific gravity comparable to normal aggregate. We present MNW recycling as a partial replacement for fine aggregates and electric arc furnace steel slag (EAFSS) as coarse aggregates to produce sustainable heavyweight concrete (HWC). Our main research aim was to study the radiation shielding and mechanical properties of sustainable HWC by partially replacing MNW with 10, 20, 30, and 40% sand. EAFSS is a coarse aggregate for 60% of the total volume. Fresh and hardened properties of HWC are presented. Furthermore, we analysed the internal structure of HWC mixes using a scanning electron microscope. Our results showed the positive effects of MNW on the unit weight of concrete. The density of HWC mixes ranges between 2650 and 3170 kg/m³. In addition, MNW contributes to increasing the compressive strength of concrete mixes with their use of up to 30%. Therefore, the MNW ratios improved the failure behaviour of HWC mixes. The improved linear attenuation coefficient of HWC mixes was due to using MNW ratios and higher densities than the reference mix.

Two unique approaches were proposed to strengthen the bond between the glass fiber reinforcement polymer (GFRP) and the RC concrete surfaces. The two bonding materials are epoxy (EP) and geopolymer (GPP) with different ratios of short glass fibers (SGF). The experimental program includes seven reinforced concrete (RC) beams that have the same cross-section (150 mm × 200 mm) and are 1500 mm in length. The first beam is the control beam (B0-Control). The next three beams B1-0-GPP, B2-0.6-GPP, and B3-1.2-GPP have GPP with SGF ratios of 0%, 0.6%, and 1.2%, respectively. The last three beams B4-0-EP, B5-0.6-EP, and B6-1.2-EP have EP with SGF ratios of 0%, 0.6%, and 1.2%, respectively. The results show that the failure loads of beams B1-0-GPP, B2-0.60-GPP, and B3-1.2-GPP are greater than the control beam B0-Control by approximately 20.80%, 25.60%, and 31.40%, respectively, whereas the failure loads of beams B4-0-EP, B5-0.6-EP, and B6-1.2-EP are greater than the B0-Control by approximately 16.90%, 26.90%, and 26.10%, respectively; it is also noted that debonding occurs. In addition to the adhesive material, GPP has a great effect on increasing the beam’s failure load capacity due to the enhanced interfacial bond shear strength. Additionally, a finite-element program ABAQUS is performed to verify the experimental results.

This paper presents the experimental study and finite element modeling of the flexural behavior of concrete beams reinforced with reused steel bars as longitudinal reinforcements. The experimental program and results of eight reinforced concrete (RC) beams constructed with and without reused steel bars are described in detail. The replacement percentages of brand‐new bars with reused steel bars in the tested beams were 50% and 100%. The reused steel bars were coated with and without epoxy. Steel fibers with fractions of 0.5% and 1.0% of the concrete volume were added to the concrete mixes. The load‐deflection relationship, ductility index, toughness, and failure modes of the tested beams are presented and discussed. It is shown that utilizing reused steel bars decreases the ultimate load of RC beams but increases their deflection at the ultimate load compared with the control beam. Increasing the steel fiber ratio increases the ultimate load and the deflection at the ultimate load of RC beams incorporating reused steel bars. However, the zinc‐rich epoxy used to coat the reused steel bars does not affect the behavior of the beams. Three‐dimensional nonlinear finite element (FE) models of the tested beams were developed using ABAQUS and validated against the test results. The developed FE models are capable of accurately simulating the experimentally observed behavior of RC beams with reused steel bars.