Chien-Hung Lin

Prof. Dr. Chien-Hung Lin

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 October 2021 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
DCDar-Yuan Chang
Dar-Yuan Chang
CLChien-Hung Lin
Chien-Hung Lin
XWXing-Yao Wu
Xing-Yao Wu
CYChun-Chun Yang
Chun-Chun Yang
SCShan-Chao Chou
Shan-Chao Chou
Polyetheretherketone (PEEK) is one of the semi-crystalline thermoplastic polymers with excellent machinability and chemical stability applied to precise structural plates and electronic components. This study installed multiple sensors to analyze the machining characteristics in the PEEK drilling. According to the time domain signals, the effects of spindle speed and feed rate on the machining characteristics of cutting force and vibration were investigated. In addition, an infrared thermography was installed to record the temperature variation within the drilling area. The experimental hole was 2-mm diameter with a 4.5-mm depth. Experimental results showed that the effect of the feed rate on thrust force is greater than the spindle speed; drilling by a low-level spindle speed with a low-level feed rate can obtain the smallest cutting force and acceleration amplitude in the spindle axis; the temperature within the drilling area is inverse to the feed rate and a high-level feed rate is helpful for forming regular curl chips. When adequate airflow was applied during the drilling operation, the hole’s shrinkage ratio and roundness can be decreased. The data presented in this paper provide valuable references for realizing the drilling of the thermoplastic—PEEK.

1 August 2023 in Materials Research Express
Verified
Journal Article
Open access
CLChien-Hung Lin
Chien-Hung Lin
BGBo-Yi Guo
Bo-Yi Guo
The utilization of a three dimension (3D) printing for the fabrication of micro-electromechanical system (MEMS) sensors presents various advantages including low cost, customization, simplicity, and speed. This study involved conducting mechanical and electrical analyses on three types of dielectric layer structures using the finite element method. Capacitive force sensors were produced through 3D printing using fused deposition modeling (FDM). The sensitivity and stiffness of the sensors were determined by measuring their capacitance and displacement changes under force using a self-made measurement system. The experimental results indicate that pre-heating the dielectric layer can reduce the hysteresis effects. In terms of more complex structures, stringing phenomena during the printing process can compromise the reliability of the sensor. A suitable dielectric layer structure can be designed based on the measurement range and sensitivity of the sensor. The results of this study demonstrate the potential for additive manufacturing to replace conventional MEMS processes in sensor production. With the advancement of FDM printing technology, it is increasingly feasible to apply 3D printing technology to sensor manufacturing in the future.


16 January 2022 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
DCDar-Yuan Chang
Dar-Yuan Chang
CLChien-Hung Lin
Chien-Hung Lin
XWXing-Yao Wu
Xing-Yao Wu

6 July 2021 in Research Square
Verified
Preprint
Open access
PDF file
DCDar-Yuan Chang
Dar-Yuan Chang
CLChien-Hung Lin
Chien-Hung Lin
XWXing-Yao Wu
Xing-Yao Wu
Engineering plastics have specific properties in the strength, hardness, impact resistance, and aging persistence, often used for structural plates and electronic components. However, the holes made by the drilling process always shrink after the cutting heat dispersion due to their high thermal expansion coefficient. Especially for small-hole fabrication, drilling parameters must be discussed thoughtfully to acquire a stable hole quality. This study developed parameter models by the Taguchi-based neural network method to save the experimental resources on drilling of engineering plastic, polyetheretherketone (PEEK). A three-level full-factorial orthogonal array experiment, L27, was first conducted for minimizing the thrust force, hole shrinkage in diameter, and roundness error. The experiments were operated by a peck-drilling process with cyclic lubricant, and the diameter was 1 mm. In terms of the network modeling, four variables were designated to the input layer neurons including the spindle speed, depth of peck-drilling, feed rate, and thrust force detected; and that of the output layer were the diameter shrinkage and roundness of the hole drilled. The models were trained by a stepped-learning procedure to expand the network’s field information stage by stage. After three stages of training, the models developed can provide precise simulations for the network’s training sets and accurately predict the hole’s characteristics for the non-trained cases.

18 September 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
CLChien-Hung Lin
Chien-Hung Lin
CKChen-Hao Ku
Chen-Hao Ku
FHFan-Chun Hsieh
Fan-Chun Hsieh
This study presents a methodology for balancing surface integrity, densification, and hardness in selective laser melting (SLM) of 316L stainless steel. While SLM offers unparalleled geometric freedom, achieving optimal performance is often hindered by trade-offs among process parameters. To address this, a high-fidelity predictive and optimization framework was established by integrating response surface methodology (RSM) with Taguchi-based grey relational analysis (GRA). A Taguchi L9 orthogonal array with analysis of variance (ANOVA) was implemented to identify the discrete influences of laser power, scanning speed, hatch spacing, and scanning pattern. Reduced quadratic RSM models were then developed to capture nonlinear interactions. Statistical validation yielded coefficients of determination (R2) of 85.6% for surface roughness and 80.7% for hardness, with a mean absolute error within 2.5% of average response values. Interactive response surface analysis revealed that surface roughness improves monotonically with energy density, whereas hardness exhibits a convex behavior governed by the synergy between laser power and scanning speed. Multi-objective optimization through GRA identified the optimal parameter set as 180 W laser power, 500 mm/s scanning speed, 0.08 mm hatch spacing, and a spiral scanning pattern. Validation experiments produced a balanced profile of 8.45 μm surface roughness, 0.79% porosity, and 207.8 HV hardness, closely matching analytical predictions. Compared to single-objective optimization, the integrated GRA approach effectively reconciled contradictory optimization trajectories, providing a robust strategy for fabricating high-performance 316L components for demanding industrial and biomedical applications.