In this paper, single-diode model (SDM) and double-diode model (DDM) parameters of the French RTC solar cell and the Photowatt PWP 201 photovoltaic (PV) module were extracted by combining five metaheuristic algorithms with three simulation current calculation methods (i.e., approximation method, Lambert W method and Newton–Raphson method), respectively. It was found that the parameter-extraction accuracies of the Lambert W (LW) method and the Newton–Raphson (NR) method are always approximately equal and higher than that of the approximation method. The best RMSEs (root mean square error) obtained by using the LW or the NR method on the solar cell and the PV module are 7.72986 × 10−4 and 2.05296 × 10−3 for SDM parameter extraction and 6.93709 × 10−4 and 1.99051 × 10−3 for DDM parameter extraction, respectively. The latter may be the highest parameter-extraction accuracy reported on the solar cell and the PV module so far, which is due to the adoption of more reasonable DDM parameter boundaries. Furthermore, the convergence curves of the LW and the NR method basically coincide, with a convergence speed faster than that of the approximation method. The robustness of a parameter-extraction method is mainly determined by the metaheuristic algorithm, but it is also affected by the simulation current calculation method and the parameter-extraction object. In a word, the approximation method is not suitable for application in PV-model parameter extraction because of incorrect estimation of the simulation current and the RMSE, while the LW and NR methods are suitable for the application for accurately calculating the simulation current and RMSE. In terms of saving computation resources and time, the NR method is superior to the LW method.
In this paper, the explicit equation of the single diode model (SDM) expressed by the Lambert W function was reduced to its simplified form through variable replacement; then the simplified explicit equation was combined with an intelligent optimization algorithm to estimate the SDM parameters of solar cells and PV modules. To evaluate the parameter extraction performance of the new method, eight typical intelligent optimization algorithms were combined with the implicit, explicit, and simplified explicit equation to extract the SDM parameters of a solar cell and three types of PV modules. The results show that the new method not only improves the accuracy of parameter extraction but also enhances the robustness and convergence speed. Most importantly, the new method can nearly improve the parameter extraction accuracy of a poor-performing algorithm in traditional methods to the level of other well-performing algorithms without enhancing the algorithm itself. In a word, this study offers a new choice for a more accurate and reliable extraction of SDM parameters from both solar cells and PV modules.
8 November 2023 in Physical Chemistry Chemical Physics
Interface molecular passivation is widely utilized to improve the performance and stability of perovskite solar cells (PSCs). However, designing efficient passivation molecules is still challenging. Owing to the fast development of machine learning (ML) methods, screening passivation molecules from molecular libraries with ML models becomes promising. Herein, 3D-MoRSE descriptor sets were introduced to predict the device power conversion efficiency (PCE) by machine learning with automatic relevance determination regression. By fine tuning the scale factor (sL), we found that sL from 0.04 to 0.50 could achieve satisfactory prediction results, and convergence is achieved at s × sL ≈ 1.40. Among all investigated atomic properties, atomic electronegativity and ionization potential revealed a strong correlation with PCE. We identified that molecules with abundant carbon-nitride single or partial-double bonds may achieve good surface passivation and realize high PCE. The highest coefficient of determination (R2) of 0.87 was achieved, demonstrating an improvement of approximately 0.11 compared to existing models. Using our optimal models, we predicted the PCEs of the devices with passivated molecules from the PubChem database, and three molecules in the top 15 candidates show good passivation ability in reported experiments. This work provides a simple and efficient method for molecule description for highly accurate ML predictions, which could accelerate the discovery of new molecules for PSC passivation.
20 June 2019 in International Journal of Photoenergy
In this paper, boron-doped Czochralski silicon (Cz-Si) wafers were fabricated into PERC solar cells by using the industrial standard process; then, the as-prepared PERC solar cells were treated by the regeneration process using electrical injection and heating and the effects of different regeneration processes (temperature, time, and injection current) on the anti-light-induced degradation (anti-LID) performance of the PERC solar cells were investigated. The results show that under the condition of 10 A injection current and 30 min processing time, the optimal processing temperature is about 180°C for PERC solar cells to obtain the best anti-LID performance. Under the conditions of a temperature of 180°C, an injection current of 10 A, and a processing time of 0-30 min, the anti-LID performance of the PERC solar cells is enhanced with the increase in the processing time. When the processing time is 20 and 30 min, the efficiency, the short-circuit current, and the open-circuit voltage of the processed PERC solar cells are slightly higher than the initial values before the regeneration and remain stable in the subsequent 12-hour light degradation process at 45°C and 1-sun illumination. At a temperature of 180°C and a processing time of 30 min, the injection current of 6 A is enough to obtain a good regeneration effect, but the optimal injection current is around 10 A.
25 August 2012 in Science China Technological Sciences