Eleni Douvi

Dr. Eleni Douvi

University of Patras, Patras, Achaea, Greece
orcid
Independent Researcher

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2021 in International Journal of Thermofluids
Verified
Journal Article
Open access
EDEleni Douvi
Eleni Douvi
CPChristos Pagkalos
Christos Pagkalos
GDGeorge Dogkas
George Dogkas
MKMARIA K. KOUKOU
MARIA K. KOUKOU
Vassilis StathopoulosVassilis Stathopoulos
Vassilis Stathopoulos
MVMichail Gr. Vrachopoulos
Michail Gr. Vrachopoulos


20 November 2023 in Energies
Verified
Journal Article
Open access
PDF file
EDEleni Douvi
Eleni Douvi
DDDimitra Douvi
Dimitra Douvi
This paper provides a review of the aerodynamic behavior of horizontal axis wind turbines operating in hazardous environmental conditions. Over the past decade, renewable energy use has accelerated due to global warming, depleting fossil fuel reserves, and stricter environmental regulations. Among renewable options, solar and wind energy have shown economic viability and global growth. Horizontal axis wind turbines offer promising solutions for sustainable energy demand. Since wind turbines operate in an open environment, their efficiency depends on environmental conditions. Hazard environmental conditions, such as icing, rainfall, hailstorms, dust or sand, insects’ collisions, increased humidity, and sea spray, result in degraded aerodynamic characteristics. The outcome of most studies has been that the airfoils’ lift is degraded, and at the same time, drag is increased when wind turbines operate under these conditions. The objective of this review is to improve our comprehension of these crucial aspects so they are taken into account when designing wind turbine blades, and it offers suggestions for future research paths. It serves as a valuable resource that can inspire researchers who are dedicated to enhancing the aerodynamic characteristics of horizontal axis wind turbines.

29 September 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
EDEleni Douvi
Eleni Douvi
DDDimitra Douvi
Dimitra Douvi
This paper provides a review of the aerodynamic behavior of horizontal axis wind turbines operating in hazardous environmental conditions. Over the past decade, renewable energy use has accelerated due to global warming, depleting fossil fuel reserves, and stricter environmental regulations. Among renewable options, solar and wind energy have shown economic viability and global growth. Horizontal axis wind turbines offer promising solutions for sustainable energy demand. Since wind turbines operate in an open environment, their efficiency depends on environmental conditions. Hazard environmental conditions, such as icing, rainfall, hailstorm, dust or sand, insects’ collisions, increased humidity and sea spray, result in degraded aerodynamic performance. The outcome of the most studies is that lift is degraded and at the same time drag is increased when wind turbines operate under these conditions. The objective of this review is to improve our comprehension of the crucial aspects to take into account when designing wind turbine blades, and it offers suggestions for future research paths. It serves as a valuable resource that can inspire researchers who are dedicated to enhancing the aerodynamic performance of horizontal axis wind turbines.

23 December 2022 in Inventions
Verified
Journal Article
Open access
PDF file
DDDimitra Douvi
Dimitra Douvi
EDEleni Douvi
Eleni Douvi
DMDionissios Margaris
Dionissios Margaris
The main purpose of this study is to develop an understanding of the aerodynamic performance of a horizontal axis wind turbine (HAWT) operating in a dusty environment, with various concentration of dust in the flow domain. The computational analysis was accomplished by the commercial computational fluid dynamics (CFD) code ANSYS Fluent 16.0. Initially, a user-friendly developed application was utilized for the optimum blade geometry special characteristics calculation. The design of the HAWT rotor and meshing of the computational domain follows. The moving reference frame (MRF) model was applied for the rotary motion of the blades, the dust was added in the computational domain by the discrete phase model (DPM) and SST k–ω turbulence model was enabled. The power output of the studied HAWT, operating in several dusty environments, was estimated and compared with the power output of a particular HAWT in clean air. The flow field around the HAWT rotor, including the contours of pressure, particles dissipation rate and erosion rate on both blade sides, are shown. In general, it is concluded that the operation of a HAWT in a dusty environment results in degraded performance, due to the particles deposition on the blades.

2 February 2022 in Energies
Verified
Journal Article
Open access
PDF file
MKMARIA K. KOUKOU
MARIA K. KOUKOU
CPChristos Pagkalos
Christos Pagkalos
GDGeorge Dogkas
George Dogkas
MVMichail Gr. VRACHOPOULOS
Michail Gr. VRACHOPOULOS
EDEleni Douvi
Eleni Douvi
PPPapadopoulos Polycarpos
Papadopoulos Polycarpos
A numerical study was carried out to investigate charging and discharging processes of different phase change materials (PCMs) used for thermal storage in an innovative solar collector, targeting domestic hot water (DHW) requirements. The aim was to study PCMs that meet all application requirements, considering their thermal performance in terms of stored and retrieved energy, outlet temperatures, and water flow rate. Work was carried out for three flat-plate solar panels of different sizes. For each panel, a PCM tank with a heat exchanger was attached on the back plate. Simulations were conducted on a 2D domain using the enthalpy–porosity technique. Three paraffin-based PCMs were studied, two (A53, P53) with phase-change temperatures of approximately 53 °C and one of approximately 58 °C (A58H). Results showed that, during charging, A58H can store the most energy and A53 the least (12.30 kWh and 10.54 kWh, respectively, for the biggest unit). However, the biggest unit, A58H, takes the most time to be fully charged, i.e., 6.43 h for the fastest feed rate, while the A53 unit charges the fastest, at 4.25 h. The behavior of P53 lies in between A53 and A58H, considering stored energy and charging time. During discharging, all PCMs could provide an adequate DHW amount, even in the worst case, that is, a small unit with a high hot water consumption rate. The A58H unit provides hot water above 40 °C for 10 min, P53 for 11 min, and A53 for 12 min. The DHW production duration increased if a bigger unit was used or if the consumption rate was lower.