We proposed a joint time and frequency transfer scheme over a single International Telecommunication Union 100 GHz wavelength division multiplexing (WDM) channel using a normal commercial WDM device and commercial offset WDM device. A standard 100 GHz WDM channel is divided into three sub-channels with a frequency interval of more than 20 GHz for a time and frequency transfer, which could help to avoid the interference among time, frequency, and data signals in other WDM channels. A joint high-precision time and frequency transfer is, therefore, able to be performed with data transmission over WDM optical communication links without extra requirements on devices. A joint time and frequency transfer in a single 100 GHz WDM channel is experimentally demonstrated over a 60 km fiber link with the communication data transmission in the adjacent channels. The stability of the time transfer can be better than 15 ps at 1 s, and the stability of the frequency transfer can be better than 2.7×10−14 at 1 s, while the bit error rates of the adjacent channels are at the same level as the separate transmission.
22 February 2024 in IEEE Transactions on Instrumentation and Measurement
In this paper, we proposed a scheme to detect and locate non-reciprocal links based on the correlation of routes in a time transfer network. Different routes between two stations in networks synthesize several ring routes. The reciprocity of each ring route is determined based on the clockwise and the counterclockwise propagation delays of the corresponding ring route measured at the same station. The non-reciprocal links in the non-reciprocal ring route are further located according to the correlation of multiple routes in the time transfer network. The sufficient and necessary conditions for locating non-reciprocal links is presented and proved. The proposed scheme is validated using simulation in a transmission network with 8 stations and 14 links. In addition, the identifying and locating accuracy of the proposed scheme is analyzed in relation to the number of available links between the two stations and the reciprocity detected error probability of the non-reciprocal links in a reciprocal ring route.
30 October 2024 in IEEE Transactions on Instrumentation and Measurement
In this paper, we proposed a high-precision fiber-optic time transfer scheme based on bidirectional frequency division multiplexing and cross-correlation processing. Time signals at different stations are encoded as different time varying signals within different frequency passband, respectively. The transferred time varying signals are carried on the same wavelengths and transmitted to each other, which are precisely recovered at the receiving stations. The time differences between the received time varying signals and the one generated according to the local time signals are measured by cross correlation processing. Since the transferred time varying signals are non-overlapping on spectrum, back-scattering noises from fiber links can be effectively suppressed by simply electrical filtering. At the same time, the symmetry of bidirectional transmission can be guaranteed maximally to avoid the time-consuming and laborious link calibration, and support fiber link switching without requiring link re-calibration. The proposed scheme is experimentally demonstrated over 50 km, 100 km, 150 km fiber-links, respectively. The results show that the measured mean clock difference can be less than 3.55 ps over fibers with different lengths, and the stability in terms of time deviation can be less than 34.46 ps at 1 s and 1.26 ps at 1000 s over 150 km fiber-link, respectively.
13 January 2025 in IEEE Internet of Things Journal
Network architectural is indispensable for a wide-area and robust fiber-optic time transfer network, however, there is currently a deficiency in effective scheme. This paper proposed a reconfigurable fiber-optic time transfer network architecture based on Software-Defined time transfer units, enhancing the network’s capability for flexible resource allocation, automatic protection and restoration. The architecture consists of three layers: (1) Time Transfer Layer for time signal transmission and clock difference cancellation; (2) Monitor & Control Layer for monitoring network states, fault detection, and dynamic reconfiguration of the Software-Defined time transfer units; (3) Service & Configuration Layer for customizable service construction and proactive network reconfiguration. A polymorphic Software-Defined time transfer unit is further designed, which can operate as a master station, intermediate station, and slave station using the same hardware. The proposed architecture and the designed Software-Defined time transfer unit are experimentally demonstrated over chained and ring networks, respectively. Network expansion, contraction, topology reconfiguration, failure and fault recovery are validated. The changes of measured mean clock differences are below 43 ps across different scenarios, verifying the robustness and flexibility of the proposed architecture.
SummaryWe report on a high-precision fiber-optic time transfer system over single optical fiber utilizing the same wavelength in both directions based on bidirectional frequency division multiplexing and cross correlation processing (BFDM-CR). The probe signals and the backscattering noises are effectively discriminated by electrical bandpass filtering for the non-overlapping spectrum of the bidirectional transmission signals. In this way, the impact of the Rayleigh backscattering and the dispersion-induced symmetric deviation over fiber link can be suppressed at the same time. The time interval of the received signals and the local signals is obtained by cross correlation processing to improve the SNR of the measurement on the time interval. A time transfer system based on BFDM-CR over 50km fiber-link is experimentally demonstrated. The stabilities in terms of time deviation (TDEV) are less than 19.2 ps/s and 2.2 ps/10000s, respectively.
11 February 2025 in IEEE Open Journal of Ultrasonics, Ferroelectrics, and Frequency Control
In this letter, we proposed a point-to-multipoint fiber-optic time transfer scheme over a star-shaped fiber network based on bidirectional frequency division multiplexing without requiring link calibration. The time signals at the local station and remote stations are encoded into time-varying signals within in different spectral passbands, respectively. The optical carriers with the same wavelength are employed to transfer the two time-varying signals in both directions over a single fiber. The backscattering noises from fiber links can be effectively suppressed by simply electrical filtering due to the non-overlapping on spectrum between the forward and backward time-varying signals. The local station broadcasts the time signal of the reference clock to all remote stations based on space division multiplexing to support point-to-multipoint fiber-optic time transfer. The proposed scheme is demonstrated over a star-shaped fiber network with two remote stations. The results show that the measured mean clock difference can be less than -1.03 ps and 4.99 ps without link calibration, respectively. The measured time stability in terms of time deviation is better than 19.93 ps@1s, 0.50 ps@1000s and 25.35 ps@1s, 0.65 ps@1000s.