Most primary energy sources, such as the fossil fuels of oil, coal, and natural gas, produce waste heat. Recycling of this unused thermal energy is necessary in order to increase the efficiency of usage. Thermoelectric (TE) conversion technologies, by which waste heat is directly converted into electricity, have been extensively studied, and the development of these technologies has continued. TE power-generation has attracted significant attention for use in self-powered wireless sensors, which are important for our increasingly sophisticated information society. For the middle-temperature range (i.e., 600–900 K), with applications such as automobiles, intensive studies of high-performance TE materials have been conducted. In this study, we review our recent experimental and theoretical studies on alkaline-earth silicide Mg2Si TE materials, which consist of nontoxic abundant earth elements. We demonstrate improvements in TE performance brought about by lightly doping Mg2Si with isoelectronic impurities. Furthermore, we examine the electrode formation and material coatings. Finally, we simulate the exhaust heat requirements for the practical application of TE generators.
Thermoelectric power generation in the low temperature region has attracted considerable attention as a means of the effective use of distributed energy and for sensor applications. However, it is difficult to theoretically predict the exact thermoelectric transport properties owing to the relatively narrow bandgap of low temperature thermoelectric materials. In this study, a high-purity α-SrSi2 crystal was synthesized by the vertical Bridgman (VB) method. The carrier density of the VB-grown α-SrSi2 was investigated, and, from the temperature dependence of the carrier density, it was estimated that the bandgap was 13.1 meV. First-principles calculations using the Heyd–Scuseria–Ernzerhof screened hybrid functional for α-SrSi2 predicted the bandgap to be very close to this value (13.27 meV) when assuming the mixing parameter of the Hartree–Fock contribution to the exact exchange is 18.7%. Using the calculated electronic structure and the measured carrier concentration, the predicted temperature dependence of the Seebeck coefficient was in good agreement with the experimental results.
Efficient thermal management in stretchable electronics demands materials that seamlessly integrate high thermal conductivity, mechanical flexibility, and reliable interface stability. This paper presents a stretchable, thermally conductive, biphasic, liquid‐metal sheet (LM sheet)—formed by dispersing copper particles in gallium‐based liquid metal—encapsulated between nanoscale styrene–butadiene–styrene elastomer layers. This trilayer architecture establishes continuous thermal‐conduction pathways while providing excellent electrical insulation and corrosion resistance. The LM sheet achieves impressive in‐plane and through‐plane thermal conductivities (40.4 and 16.7 W m −1 K −1 , respectively), with an elongation at break >200%. Notably, it retains 96% of its thermal conductivity even under 100% tensile strain. It adheres strongly to various substrates without adhesives, excellently spreading heat in flexible heaters and stretchable LED devices under both static and stretched conditions. This paper presents a compelling strategy for developing next‐generation thermal‐interface materials for deformable and skin‐integrated electronic systems.
Interest in thermoelectric (TE) materials has revived in recent years because TE materials realize not only the utilization of distributed unused thermal energy, such as exhaust heat from automobiles and factories and solar heat, but also cold power generators and self-power supplies for wireless sensors. However, because the bandgap of low-temperature TE materials is relatively small, the precise calculation of its physical properties is difficult to achieve by first-principles calculations based on conventional density functional theory. The present study investigates the effects of isotropic strain and incorporation of isoelectronic impurities on the TE transport properties of extremely narrow-gap semiconducting α-SrSi2. By adopting the Gaussian–Perdew–Burke–Ernzerhof hybrid functional, the analysis clarifies the relationship between the lattice distortion and the electronic structure in α-Sr4–xAxBySi8–y (A = Mg, Ca, or Ba; B = C, Ge, Sn, or Pb) and elucidates the TE transport properties. In particular, an irregular bandgap expansion was observed in α-Sr4CSi7, suggesting that the TE performance can be maximized by appropriate tuning of the carrier concentration.