Zhaoming Mai

Mr. Zhaoming Mai

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 December 2022 in Combustion and Flame
Verified
Journal Article
Closed access
Yingtao WuYingtao Wu
Yingtao Wu
XKXiangdong Kong
Xiangdong Kong
TYTao Yu
Tao Yu
ZMZhaoming Mai
Zhaoming Mai
SCShutong Cao
Shutong Cao
CTChenglong Tang
Chenglong Tang

25 June 2024 in Applied Thermal Engineering
Verified
Journal Article
Closed access
WWWei Wang
Wei Wang
ZMZhaoming Mai
Zhaoming Mai
XYXiaoxin Yao
Xiaoxin Yao
Chenglong TangChenglong Tang
Chenglong Tang
ZHZuohua Huang
Zuohua Huang

31 May 2024 in Combustion and Flame
Verified
Journal Article
Closed access
ZMZhaoming Mai
Zhaoming Mai
Yingtao WuYingtao Wu
Yingtao Wu
Chenglong TangChenglong Tang
Chenglong Tang
HMHaibao Mu
Haibao Mu
WWWei Wang
Wei Wang
ZHZuohua Huang
Zuohua Huang

7 September 2023 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
ZMZhaoming Mai
Zhaoming Mai
Chenglong TangChenglong Tang
Chenglong Tang
YLYu Li
Yu Li
Yingtao WuYingtao Wu
Yingtao Wu
ZHZuohua Huang
Zuohua Huang
Spray auto-ignition is a complex physical and chemical process whose mechanism is still not well understood. This paper explores the contribution of physical and chemical mechanisms to spray auto-ignition and combustion behaviors over a wide range of ambient temperature and pressure conditions in an optical rapid compression machine. Specifically, the spray development and ignition process are first visualized and the spray ignition delay times (IDTI) are measured through high-speed imaging. IDTI is then compared with gas phase chemical ignition delay times (IDTC) calculated by 0D homogeneous reactor simulation. Subsequently, different combustion modes are recognized by analyzing the mixture status at the instant of ignition, the spray flame behavior, and the pressure evolution history. Finally, a regime diagram of combustion modes is proposed to illustrate the dominant mechanisms for different spray combustion modes. Results show that the measured spray IDTI is longer than the 0D calculated IDTC due to the physical delay caused by spray development, evaporation, and mixing. At higher temperatures and pressures, the difference between IDTI and IDTC is increased because the evaporation and mixing become progressively important, compared to the chemical reaction mechanism. Scrutinization on the pressure and the apparent heat release rate evolution curve reveals that with the increase of the temperature and pressure, the chemical-controlled combustion time accounts for less and less of the total combustion duration. This further indicates that spray ignition and combustion behaviors transit from chemical-dominated mode to mixing-dominated mode.

22 July 2022 in Machines
Verified
Journal Article
Open access
PDF file
ZMZhaoming Mai
Zhaoming Mai
YLYang Liu
Yang Liu
Chenglong TangChenglong Tang
Chenglong Tang
ZHZuohua Huang
Zuohua Huang
To facilitate the better use of RP-3 kerosene in compression ignition engines, the auto-ignition behaviors of RP-3 kerosene spray were experimentally investigated in an optical rapid compression machine. Results show that most of the tests have good ignitability and combustion performance. For all the successful ignited cases, the flame kernel was found to be formed before the steep rise of pressure, which explained that image-based ignition delay time is always shorter than the pressure-based ignition delay time. The effects of ambient environment, injection pressure, and injection delay time on the pressure history, ignition intensity, combustion duration, heat release rate, and other parameters were investigated individually. The ambient environment has a strong influence on ignition delay time by accelerating the chemical reactions, whereas the high injection pressure helps the better vaporization of fuel spray. The effect of injection delay time is non-monotonic as the trade-off relation between heat loss and blending of fuel and oxygen. The heat release rate histories under different conditions were compared and analyzed, and the two-stage heat release phenomenon was observed in the negative temperature coefficient region. The ignition intensity region was determined based on the measured ignition delay times of RP-3 kerosene spray, and multiple linear regression correlation was used to study the ignition delay time sensitivity to multi-factors.

8 July 2024 in Proceedings of the Combustion Institute
Verified
Journal Article
Closed access
ZMZhaoming Mai
Zhaoming Mai
Yingtao WuYingtao Wu
Yingtao Wu
CTChenglong Tang
Chenglong Tang
ZHZuohua Huang
Zuohua Huang