This study proposes an electromagnetic shielding material sprayed with silver-coated copper powder (core-shell powder). The shielding properties of the material are analyzed in details section. Cross-sectional observation and sheet resistance measurement were used to determine the thickness and electrical conductivity of the electromagnetic shielding layer, which was generated by spray-coating; this aided in confirming the uniformity of the coating film. The results indicate that the electromagnetic interference shielding effectiveness increases when the silver-coated copper paste (core-shell paste) is used as the coating material rather than the conventional aluminum base. The proposed material can be used in various frequency ranges owing to the excellent shielding effectiveness of the core-shell paste used in this study. Further investigations on the optimized spray-coating type of electromagnetic shielding material are required based on the composition of the core-shell paste and the thickness of the coating film.

This study proposes an isotropic composite material with enhanced elastic properties based on a reinforcement mechanism using ultra-high molecular weight polyethylene (UHMWPE) spherical molecules. Elastic properties are predicted through finite element analysis by randomly mixing UHMWPE using polypropylene (PP) as a matrix. The change in elastic properties of the composite is calculated for volume fractions of UHMWPE from 10 to 70%. Furthermore, the results of finite element analysis are compared and analyzed using a numerical approach. The results show that the physical properties of the composite material are enhanced by the excellent elastic properties of the UHMWPE, and the finite element analysis results confirm that it is effective up to a volume fraction of 35%.

In this study, we calculated the elastic properties of polypropylene composites mixed with ultrahigh-molecular-weight polyethylene (UHMWPE) fibers. We applied micromechanics models that use numerical analysis, conducted finite element analysis using the homogenization method, and comparatively analyzed the characteristics of polypropylene (PP) containing UHMWPE fibers as reinforcement. The results demonstrate that elastic properties improved as the volume fraction of UHMWPE fiber increased. It was confirmed that the fibers had anisotropic elastic properties due to the shape of the fibers. In addition, it is necessary to compare these findings with future experimental results to obtain data for developing UHMWPE–PP composites.

In this study, to improve the mechanical properties of polypropylene (PP) with the objective of developing a composite with ultra-high-molecular-weight polyethylene (UHMWPE) as a reinforcement, the mechanical properties of the composite material were investigated via numerical analysis and finite element analysis (FEA). Based on a mathematical approach, the modulus of elasticity, shear modulus, and Poisson’s ratio were calculated using a numerical model, and, through FEA with application of the homogenization method, the elastic properties were predicted, and the results were comparatively analyzed. In the future, it will be necessary to compare experimental and numerical analysis results to verify the findings of this study.

This study evaluated the properties of 3D-printed Onyx–fiberglass composites. These composites were 3D-printed with zero, one, two, three, and four layers of fiberglass. Ten samples of each configuration were printed for the tensile and flexural tests. The average tensile strength of the Onyx specimens was calculated to be 44.79 MPa, which increased linearly by approximately 20–25 MPa with each additional fiberglass layer. The elastic moduli calculated from the micromechanics models were compared with the experimental values obtained from the tensile tests. The experimental elastic modulus increased more significantly than the model prediction when more fiberglass layers were added. The flexural modulus of Onyx was 17.6 GPa, which increased with each additional fiberglass layer. This quantitative analysis of composites fabricated using 3D printing highlights their potential for commercialization and industrial applications.

In this study, preliminary simulations were performed to manufacture thermoplastic composites that can be processed by injection. For analysis, a basalt particulate–polymer composite model was manufactured and its elastic modulus, shear modulus, thermal expansion coefficient, and thermal conductivity were predicted using finite-element analysis (FEA) and micromechanics. Polypropylene (PP), polyamide 6, polyamide 66, and polyamide (PA) were employed as the polymer matrix, with the variations in their properties investigated based on the volume fraction of basalt. The polymer–basalt composite’s properties were analyzed effectively using FEA and the micromechanics model. FEA was performed by constructing a 3D model based on the homogenization technique to analyze the effective properties. The micromechanics model was analyzed numerically using the mixture rule, and the Mital, Guth, and Halpin–Tsai models. As a result, it is best to analyze the effective properties of polymer–basalt composites using the Halpin–Tsai model, and it is necessary to conduct a comparative analysis through actual experiments. In the future, actual composite materials need to be developed and evaluated based on the findings of this study.