A photocatalytic system for decolorization of double azo reactive black 5 (RB5) dye and water disinfection of E. coli was developed. Sol gel method was employed for the synthesis of Fe-TiO2 photocatalysts and were characterized using thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy dispersive X-ray analysis (EDX), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS) and Brunauer–Emmett–Teller (BET) analysis. Results showed that photocatalytic efficiency was greatly influenced by 0.1 weight percent iron loading and 300 °C calcination temperature. The optimized reaction parameters were found to be the ambient temperature, working solution pH 6.2 and 1 mg g−1 dose to completely decolorize RB5. The isotherm studies showed that RB5 adsorption by Fe-TiO2 followed the Langmuir isotherm with maximum adsorption capacity of 42.7 mg g−1 and Kads 0.0079 L mg−1. Under illumination, the modified photocatalytic material had higher decolorization efficiency as compared to unmodified photocatalyst. Kinetic studies of the modified material under visible light irradiation indicated the reaction followed the pseudo-first-order kinetics. The illumination reaction followed the Langmuir-Hinshelwood (L-H) model as the rate of dye decolorization increased with an incremental increase in dye concentration. The L-H constant Kc was 1.5542 mg L–1∙h–1 while Kads was found 0.1317 L mg–1. The best photocatalyst showed prominent percent reduction of E. coli in 120 min. Finally, 0.1Fe-TiO2-300 could be an efficient photocatalyst and can provide a composite solution for RB5 decolorization and bacterial strain inhibition.
The rapid advancement in technology in recent years has shown that nanofluids are very vital to further development in science and technology. Moreover, many industrial specifications cannot be met by allowing natural convection only, hence the need to incorporate forced convection and natural convection into a single flow regime. The research aims to quantify the mixed convective two-phase flow past a vertical permeable surface in a Brinkman-Extended Darcy porous medium (BEDPM) induced by nanofluid, with heat and mass transfer. In addition, the Nield condition is also incorporated. The model of the problem was initially constructed in the vital form of leading governing equations (LGEs). These LGEs are specifically called partial differential equations (PDEs) (because of two or more independent variables) which were later converted into a set of the single independent variable of ordinary differential equations (ODEs) by implementing the similarity transformations. The set of single independent ODEs was numerically solved via the boundary value problem of fourth-order (bvp4c) technique. The bvp4c is one of the most frequently recommended built-in MATLAB subroutines based on the three-stage Labatto formula. The impact of several physically embedded influential parameters on the fluid flow, along with mass and thermal properties of the nanofluid in a Brinkman-Extended Darcy porous medium for the cases of buoyancy assisting flow (BAF) and buoyancy opposing flow (BOF), were investigated and argued. The numerical outcomes clarify that the porosity parameter reduces the velocity, whereas the concentration and the temperature enhance in the case of the buoyancy assisting and buoyancy opposing flows. In addition, the wall drag force elevates for the larger value of the dimensionless permeability parameter and the buoyancy ratio parameter , while it declines for the modified porosity parameter .
In this work, double rotating active cylinders and slot nanojet impingement are considered for the cooling system of a conductive panel. Colder surface temperatures of the cylinders are used, while different rotational speeds are assigned for each of the cylinders. The impacts of cylinder rotational speeds, size and distance between them on the cooling performance are evaluated. The rotational effects and size of the cylinders are found to be very effective on the overall thermal performance. At the highest rotational speeds of the cylinders, the average Nusselt number (Nu) rises by about 30.8%, while the panel temperature drops by about 5.84 C. When increasing the cylinder sizes, temperature drops become 7 C, while they are only 1.75 C when varying the distance between the cylinders. Subcooling and nanofluid utilization contributes positively to the cooling performance, while 1.25 C and 10 C temperature drops are found by varying the subcooled temperature and solid volume fraction. An artificial neural network is used for the estimation of maximum and average panel temperatures when double cylinder parameters are used as the input.
24 January 2026 in Case Studies in Thermal Engineering