Supercavitation technology has important application value in military and national defence fields because of its huge potential in drag reduction, while the cavitation around underwater moving objects may be affected by the surface properties of objects. In this paper, the supercavitation characteristics and hydrodynamics of a projectile with hydrophobic and hydrophilic surface coatings were experimentally studied using a high-speed camera. The supercavitation evolution, cavitation size, velocity change, drag force coefficient, and ballistic deflection of projectiles in different water depths are compared and analyzed. The results show that the length and diameter of the supercavity increase with the decrease in water depth. At the same water depth and cavitation number, the length and diameter of the supercavitation of the projectile with hydrophobic coating were greater than those of the projectile with hydrophilic coating, and the drag force coefficient of the hydrophobic projectile was obviously smaller than that of the hydrophilic projectile. Under the working conditions of 6.67D, 16.7D, and 33.3D, the drag force coefficient of the hydrophobic projectile could be reduced by about 20–40% compared with that of the hydrophilic projectile. The maximal reduction in drag force coefficient was up to 40% at = 0.34 under a water depth of 33.3D. The velocity attenuation of hydrophobic projectile was about 20% slower than that of hydrophilic projectile. In addition, the ballistic stability of hydrophobic coated projectiles was better than that of hydrophilic coated projectiles in the different water depths observed in the paper.
The study of the water entry of successively fired projectiles under a wave environment is of great significance for the development and application of supercavitation weapons. In this paper, the supercavitating flow field of two successively fired projectiles entering water under different wave conditions is numerically simulated by the volume of the fraction model considering the cavitation of water. The motion of projectiles is handled by the overlapping grid technology and the simulated projectiles have six degrees of freedom. The effects of different wave phases and wave heights on the supercavitating flow field and the dynamic loads of the projectiles are studied. The research results show that the wave phase has an effect on the evolution and size of the supercavitation and the effect of the wave phase on the water splash above the free surface is more obvious. The peak of the drag force of the first projectile under conditions of different wave phases with 0.12 m wave height can be reduced by about 50% compared with that under the no-wave condition. The wave phases have an effect on the peak of the drag coefficient, and for the first projectile the peak under the condition of the 180° phase is about 40% lower than that of the 0° phase. The peak of the drag coefficient of the first projectile decreases with the increase in wave height. When the wave height increases from 0.0 m to 0.05 m, the peak value decreases by about 45%. For all conditions, regardless of wave phases or wave heights, the peak of the drag coefficient of the second projectile is obviously much lower than that of the first projectile. Accordingly, the decrease in the velocity of the second projectile is far slower than that of the first one. Negative values of the drag coefficient on the second projectile are observed when the second projectile enters the cavity of the first one.
In this paper, the supercavitation of the parallel and tandem projectiles moving underwater with high-speed under the condition with/without lateral flows is numerically simulated by the volume of fraction (VOF) model. The motion of the projectiles was handled by the overlapping grid and six degrees of freedom (DOF) techniques. The supercavitation evolution and the hydrodynamic characteristics of the projectiles were analyzed for the parallel and tandem projectiles under different conditions. The results show that the cavity shape is symmetrical under the condition without lateral flows, but is no longer symmetrical under the conditions with lateral flows. The asymmetry of the cavity contour increases with the velocity of the lateral flow. For the parallel projectiles, the change trends of the axial velocity of projectile 1 and projectile 2 are nearly the same. The offset velocity of projectile 1 and projectile 2 increases with the increase in the velocity of the lateral flow. The deflection angle of projectile 1 decreases with the increase in the lateral flow velocity but that of projectile 2 increases with the increase in the lateral flow velocity. At t = 3.0 ms, the deflection angle of projectile 2 is up to 20° under the condition of the lateral flow velocity of 11.25%, while the deflection angle of projectile 1 and 2 under other conditions is in the range of 5°. For the tandem projectiles, the axial velocity of projectile 1 gradually decreases. The change trend of the axial velocity of projectile 2 at first is the same as that of projectile 1, and then the change is dependent on the velocity of the lateral flow. Under the condition of the lateral flow velocity with 11.25%Vp, projectile 2 cannot enter the cavity of the front projectile. The change trend of the axial velocity of projectile 2 is similar as but somewhat slower than that of projectile 1. For the parallel projectiles, the ballistic stability of the projectile on the oncoming side is better than that of the projectile on the backflow side. Whether parallel or tandem projectiles, the ballistic stability of projectile 2 becomes worse with the increase in the lateral flow velocity.
A two-way coupled model between polydisperse particle phases with compressible gases and a density-based coupling implicit solution method, combining the third-order MUSCL with QUICK spatial discretization scheme and the second-order temporal discretization scheme, are constructed based on the discrete-phase model (DPM) and the stochastic wander model (DRWM) in the Eulerian–Lagrangian framework in conjunction with a unitary particulate source (PSIC) approach and the SST k-ω turbulence model. The accuracy of the numerical prediction method is verified using previous supersonic nozzle gas-solid two-phase flow experiments. Numerical simulation of a two-phase jet of dry powder extinguishing agent gas with pilot-type supersonic nozzle was performed to analyze the influence of geometrical parameters, such as the length ratio rL and the area ratio rA of the main nozzle on the two-phase flow field, as well as on the jet performance indexes, such as the particle mean velocity vp,a, velocity inhomogeneity Φvp, particle dispersion Ψp, particle mean acceleration ap,a, etc. By analyzing the parameters, we indicate the requirements for the combination of jet performance metrics for different flame types such as penetrating, spreading, and dispersing.
This study examined the multi-phase flow field for a single object and two parallel/series objects under different incoming angles of lateral flow. The volume of fluid model, the Sauer–Schnerr cavitation model, and the six degrees of freedom (DOF) method were adopted to consider simulations of multi-phase flow, phase change, and object movement, respectively. The results show that, for a single object, the degree of asymmetry in the cavity profile depends on the component (the z-component) of the lateral inflow velocity in the direction perpendicular to the initial velocity of the object. As this component increases, the asymmetry of the cavity increases. The cavity length is related to the relative axial speed between the object and the water. For parallel objects, the cavity asymmetry is determined by the superimposed influence of the z-component of the lateral incoming speed and the high-pressure zone induced by the nearby object. The object located downstream relative to the lateral flow has a stronger cavity asymmetry than that of the upstream object, and the trajectory of the downstream object is more easily deviated than that of the upstream object. For tandem objects, with the increase in the lateral incoming angle, the supercavity length increases after the rear object enters into the front cavity. With the increase in the z-component of the lateral flow velocity, the deviation speed increases.