Wei Gao

Dr. Wei Gao

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 February 2021 in Polymers
Verified
Journal Article
Open access
PDF file
CLChang Liu
Chang Liu
ATAmit Tripathi
Amit Tripathi
WGWei Gao
Wei Gao
JTJohn Tsavalas
John Tsavalas
Waterborne latex is often called a product-of-process. Here, the effect of semi-batch monomer feed rate on the kinetics and gel formation in seeded emulsion polymerization was investigated for the copolymerization of n-butyl methacrylate (n-BMA) and ethylene glycol dimethacrylate (EGDMA). Strikingly, the gel fraction was observed to be significantly influenced by monomer feed rate, even while most of the experiments were performed under so-called starve-fed conditions. More flooded conditions from faster monomer feed rates, including seeded batch reactions, counterintuitively resulted in significantly higher gel fraction. Chain transfer to polymer was intentionally suppressed here via monomer selection so as to focus mechanistic insights to relate only to the influence of a divinyl monomer, as opposed to being clouded by contributions to topology from long chain branching. Simulations revealed that the dominant influence on this phenomenon was the sensitivity of primary intramolecular cyclization to the instantaneous unreacted monomer concentration, which is directly impacted by monomer feed rate. The rate constant for cyclization for these conditions was determined to be first order and 4000 s−1, approximately 4 times that typically observed for backbiting in acrylates. This concept has been explored previously for bulk and solution polymerizations, but not for emulsified reaction environments and especially for the very low mole fraction divinyl monomer. In addition, while gel fraction could be dramatically manipulated by variations in linear monomer feed rates, it could be markedly enhanced by leveraging non-linear feed profiles built from combination sequences of flooded and starved conditions. For a 2 h total feed time, a fully linear profile resulted in 30% gel while a corresponding non-linear profile with an early fast-feed segment resulted in 80% gel.

25 February 2025 in ACS Energy Letters
Verified
Journal Article
Closed access
QYQiong Yuan
Qiong Yuan
WGWei Gao
Wei Gao
JLJingbo L. Liu
Jingbo L. Liu

9 July 2024 in Environmental Science & Technology
Verified
Journal Article
Closed access
XSXiaoyu Shan
Xiaoyu Shan
PWPhilip A. Wasson
Philip A. Wasson
YRYuanQiao Rao
YuanQiao Rao
SBScott Backer
Scott Backer
LLLyndsay Leal
Lyndsay Leal
OCOtto X. Cordero
Otto X. Cordero

28 October 2019 in ACS Applied Polymer Materials
Verified
Journal Article
Closed access
MCMatthew C. D. Carter
Matthew C. D. Carter
LCLiang Chen
Liang Chen
RMRobert S. Moglia
Robert S. Moglia
PLPu Luo
Pu Luo
TRTanvi S. Ratani
Tanvi S. Ratani
RERalph C. Even
Ralph C. Even

8 October 2024 in ACS Applied Polymer Materials
Verified
Journal Article
Open access
DBDustin Britton
Dustin Britton
JSJonathan Sun
Jonathan Sun
HFHammad Ali Faizi
Hammad Ali Faizi
LYLigeng Yin
Ligeng Yin
WGWei Gao
Wei Gao
JMJin Kim Montclare
Jin Kim Montclare
Rheological modifiers are an important component in the development of skin cream (SC) chassis for personal skin care products (PSCPs). The viscous behavior of a PSCP is critical to its effectiveness where its uniformity and material strength impact its processing, storage, and delivery of active ingredients. Due to the mildly acidic environment of the skin, PSCPs require a SC that will assist in maintaining their material strength at low pHs. We have investigated a coiled-coil protein hydrogel system for the ability to possess pH-responsiveness, where physical cross-linking and material strength is controlled by pH relative to the isoelectric point (pI) of the protein. We recently designed a coiled-coil protein hydrogel variant, Q5, which possesses a relatively low pI that we hypothesized to have improved supramolecular assembly into a hydrogel at acidic conditions. We demonstrate that Q5 can retain a partial solution-to-gel transition at pH 6.0 and acts as a soft hydrogel by rheology. We further tested Q5 to act as a rheological modifier in a standard SC at pH 6.0 and pH 8.0 to test conditions mediated by pH changes in the skin environment. Q5 reveals the ability to uniquely increase material strength at low pH in comparison to a standard rheological modifier like hydroxyethyl cellulose (HEC), suggesting modular protein-based coiled-coil rheological modifiers can be used in PSCPs.

1 January 2018
Verified
Book Chapter
Closed access
WGWei Gao
Wei Gao
JCJamie Cohen
Jamie Cohen
FAFrancis Acholla
Francis Acholla
WSWenyu Su
Wenyu Su