The aim of this paper is to present the design of a sensor array based on a single substrate with various composite polymer films as active layers for gas detection. A low power, four element flexible sensor platform with heater and temperature sensor was designed. The advantages of resistive sensors are easy fabrication, simple operation, and low production cost. Composite polymer films exhibit good sensitivity to low gas concentrations at room temperatures. The principle of the designed sensor array is a change of electrical resistance in dependence of gas concentration. Polyaniline (PANI), PANI/carbon nanotubes, PANI/SnO 2 , and PANI/TiO 2 composites were used as active layers. Gas sensing properties of active layers for NH 3 , CO 2 , NO 2 , O 2 , acetone, toluene, and relative humidity were studied. PANI composites, unlike pristine PANI, exhibit good reversibility and lower temperature dependence.
3 January 2018 in Beilstein Journal of Nanotechnology
Microstructured single- and double-layered sensor devices based on p-type hydrogen-terminated nanocrystalline diamond (NCD) films and/or n-type ZnO nanorods (NRs) have been obtained via a facile microwave-plasma-enhanced chemical vapour deposition process or a hydrothermal growth procedure. The morphology and crystal structure of the synthesized materials was analysed with scanning electron microscopy, X-ray diffraction measurements and Raman spectroscopy. The gas sensing properties of the sensors based on i) NCD films, ii) ZnO nanorods, and iii) hybrid ZnO NRs/NCD structures were evaluated with respect to oxidizing (i.e., NO2, CO2) and reducing (i.e., NH3) gases at 150 °C. The hybrid ZnO NRs/NCD sensor showed a remarkably enhanced NO2 response compared to the ZnO NRs sensor. Further, inspired by this special hybrid structure, the simulation of interaction between the gas molecules (NO2 and CO2) and hybrid ZnO NRs/NCD sensor was studied using DFT calculations.
This work presents the design of a polymer-film-based sensor for gas detection. Different types of polyaniline are used as active layers. The advantages of resistive sensors with PANI layers are easy preparation and low production cost. At room temperature, polymer films have a high sensitivity to gas concentrations. The developed sensor works on the idea of electrical resistance shifting with gas concentration. Three different polymerization solutions are employed to synthesize the polyaniline (PANI) active layers (aqueous solution, sulfuric acid solution, and acetic acid solution). Active layers are evaluated in a controlled environment for their ability to detect ammonia, carbon monoxide, nitrogen monoxide, acetone, toluene, and relative humidity in synthetic air. PANI layers polymerized in acetic acid solutions exhibit good sensitivity toward ammonia.
The single- and double-layered photodetectors based on ZnO and/or detonation nanodiamond (DND) have been developed via a sequential inkjet printing on the interdigital electrode (IDE) platform using a diamond and zinc oxide precursor ink. The morphological structure of the deposited materials was visualized and analyzed by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The crystalline configuration and structural quality of ZnO and nanodiamond were investigated by X-ray Diffraction (XRD) and Raman spectroscopy. The response, response time and recovery time were measured for different UV wavelengths (365, 385, and 405 nm), light intensities, temperatures and bias voltages. ZnO/DND structure shows more than 10 times higher response and faster reactivity in comparison with a single-layered photodetector. Photoresponsivity of the double-layered photodetector (ZnO/DND) is 0.35 A·W-1 whereas bare ZnO is about 0.039 A·W-1. The interaction between UV light and ZnO/DND grains was investigated by two dimensional Silvaco TCAD simulation.
The selective detection of ammonia (NH3), nitrogen dioxide (NO2), carbon oxides (CO2 and CO), acetone ((CH3)2CO), and toluene (C6H5CH3) is investigated by means of a gas sensor array based on polyaniline nanocomposites. The array composed by seven different conductive sensors with composite sensing layers are measured and analyzed using machine learning. Statistical tools, such as principal component analysis and linear discriminant analysis, are used as dimensionality reduction methods. Five different classification methods, namely k-nearest neighbors algorithm, support vector machine, random forest, decision tree classifier, and Gaussian process classification (GPC) are compared to evaluate the accuracy of target gas determination. We found the Gaussian process classification model trained on features extracted from the data by principal component analysis to be a highly accurate method reach to 99% of the classification of six different gases.