In this paper, an adaptive method for tuning a Proportional Resonance (PR) controller for synchronization of grid-connected inverters is presented. In the proposed approach, the grid frequency is obtained by minimizing the error signal using a Frequency Locked Loop (FLL) mechanism that consists of a resonant adaptive filter and a perturbation-based extermum seeking algorithm. Simulations and experimental studies are presented to demonstrate performance of the proposed controller in face of frequency variations of an emulated grid voltage waveform. The results are compared with conventional non-adaptive methods, which indicate that performance characteristics for voltage/frequency tracking and power factor can be achieved based on the IEEE 1547 standard.
23 July 2019 in IEEE/ASME Transactions on Mechatronics
In this paper, a multiobjective extremum-seeking (MOES) approach is proposed for torque control of a permanent magnet synchronous motor and minimization of its torque ripple. The latter aspect is important in human-machine interface applications such as haptic interfaces requiring smooth torque profiles at slow speeds. The proposed MOES scheme combines an adaptive iterative learning control method with an adaptive proportional-integral (PI) controller, which makes the system less sensitive to load disturbances and improves the control performance for torque regulation during transient events. Experiments are performed on a proof-of-concept exercise machine that generates desired torque profiles and mechanical impedance based on user's preference. The performance of the proposed controller is further compared with a recently proposed adaptive PI controller. The experimental results validate the effectiveness of the proposed controller in terms of torque ripple suppression, steady-state and transient performance, and load disturbance rejection.
The interfacing of the vector-controlled voltage-source converters (VSCs) into weak grid (WG) systems can induce severe instabilities. This is attributed to interactions between the vector control of the VSCs and the high impedance of the WG. The weak connection limits the amount of active power that can be injected by the VSC to the WG. In this work, the small-signal analysis is used to derive; first, a transfer function that helps to design the controller of the VSC output voltage based on the VSC-WG accurate dynamics; second, the full-order state-space model of the VSC-WG system. A modal analysis is then conducted to develop the participation factors to characterize the influencing states on the dominant modes of the system, followed by a sensitivity analysis to evaluate the influence of the vector control gains and other parameters on the dominant modes. The results of the modal analysis confirm that instabilities at the nominal power are inevitable for VSCs connected to very weak grids (VWGs). Inspired by this shortcoming, a novel compensation method is proposed to mitigate the dynamic instability of VSCs connected to VWGs. Finally, several offline time-domain simulations and hardware-in-the-loop (HIL) real-time experiments are conducted to verify the validity of small-signal analysis, validate the effectiveness of the proposed compensation method; and investigate the performance of the system under challenging scenarios such as sudden variations in the phase angle of the grid.
29 April 2019 in IEEE Transactions on Industrial Electronics
In this paper, a multiple-input multiple output (MIMO) control system integrated with daylight harvesting is presented as a proof-of-concept system for energy-efficient greenhouse lighting. The control objective is to regulate the intensity of dimmable multi-spectrum LED fixtures for achieving desired spectral irradiance levels and color ratios while utilizing the natural sunlight as much as possible. To ensure stability and improved dynamic performance, a Smith predictor is utilized to compensate for the delay introduced into the system by the communication hardware. A stability analysis of the closed-loop system is presented considering system delay and modeling uncertainties. The proposed control system was experimentally tested in a grow-tent environment consisting of dimmable halogen lights that emulate daylight variation, multi-spectrum dimmable LED fixtures, and low-cost RGB light sensors. The results indicate that about 30% energy-savings can be achieved by using the proposed automated lighting control system.
This paper presents an intelligent horticulture lighting and monitoring system to achieve energy-efficient supplemental lighting while maintaining the light quality and intensity at desired levels in the photosynthesis spectrum. Energy-efficiency is achieved through delivering only the required net light intensity, consisting of sunlight and supplemental LED light, using an intelligent controller that does not depend on the lighting system model. To this end, an online neural-network learning control system is developed, comprised of low-cost light sensors for measuring the photosynthetic photon flux density (PPFD), dimmable LED light fixtures, cameras, and internet-of-things (IoT)-enabled firmware used for crop monitoring and performance evaluation. Experiments performed in a research greenhouse facility on the lettuce crop are presented which indicate that the system can deliver the desired Daily Light Integrals (DLIs) to the plants in the presence of changing daylight conditions. The proposed method can thus deliver the exact amount of light to a specific crop based on the required light recipes during different growth phases. The control performance is further compared with a conventional on-off time-scheduling method in terms of plant health, growth, and energy requirements. The experiments indicate that the proposed solution can reduce energy consumption per unit dry mass of lettuce by 28% when compared to existing time-scheduling methods.
In this paper, an intelligent lighting instrumentation and automation system is presented with the objective of achieving high energy-efficiency in greenhouse supplemental lighting based on the Internet of Things (IoT) technology. The system runs on a Raspbian operating system which interacts with wireless-enabled light emitting diode (LED) fixtures for plant growth, an online data server, and different light sensors including RGB and quantum sensors. The communication is achieved through RestFul API, UART, and I2C. The system is utilized to implement a feedback controller that automatically adjusts the light dimming levels and, in particular, the ratio of red and blue light intensities based on the plants’ needs. A series of experiments involving plant growth were conducted which indicate that the proposed system can achieve energy-savings up to 34%, when compared to a conventional time scheduling scheme. Additionally, the experiments demonstrate that the system can achieve a highly uniform light distribution under unpredictable natural lighting conditions while saving energy due to supplemental lighting.