To evaluate the effect of surface sealants containing different filler content on the color stability of microhybrid and nanofilled composite resins. The materials evaluated as study groups were comprised a nanofilled composite resin (Filtek Ultimate, 3M ESPE) and a microhybrid composite resin (Filtek Z250, 3M ESPE). Forty-five disc-shaped specimens (10 mm × 2 mm) were prepared from each composite resin. Each study group was divided into three subgroups: control, G-Coat Plus, and Fortify Plus (n = 15). The baseline color values (L*a*b*) of each specimen were measured using a spectrophotometer according to the CIE L*a*b* color scale. Then, the specimens were immersed in red wine for a period of 3 hours per day for 15 days (3 hours/day × 15 days). After the immersion period, the color values (L*a*b*) of each specimen were measured again. The ΔL*, Δa*, and Δb* values and the color change value (ΔE) were calculated. The data were statistically analyzed with two-way ANOVA and Duncan tests (p = 0.05). All the composite resin groups demonstrated/indicated much more color changes after immersion in red wine (ΔE > 3.3). The greater ΔE values were observed with the groups applied surface sealants than the control groups (p < 0.05). Fortify Plus further increased the ΔE values of both composite resins than G Coat Plus (p < 0.05). Filtek Ultimate showed higher ΔE values than Filtek Z250 in all the subgroups (p < 0.05). The surface sealants regardless of the filler content negatively influenced the color change of the composite resins after immersed in red wine. The microhybrid composite resin had better color stability than the nanofilled composite resin. There is no favorable effect of using surface sealants on composite resins to prevent discoloration; besides, the sealants can also increase the color alteration.
13 April 2023 in Journal of the Mechanical Behavior of Biomedical Materials
The purpose of this study was to evaluate the effect of ionizing radiation from high energy X-ray on fluoride release, surface roughness, flexural strength, and surface chemical composition of the materials. The study groups comprised five different restorative materials: Beautifil II, GCP Glass Fill, Amalgomer CR, Zirconomer, and Fuji IX GP. Twenty disk-shaped specimens (8x2 mm) for fluoride release and 20 bar-shaped specimens (25 x 2x 2 mm) for flexural strength were prepared from each material. Each material group was divided into two subgroups: irradiated (IR) and non-irradiated (Non-IR). The specimens from IR groups were irradiated with 1.8 Gy/day for 39 days (total IR = 70.2 Gy). The amount of fluoride released into deionized water was measured using a fluoride ion-selective electrode and ion analyzer after 24 hours and on days 2, 3, 7, 15, 21, 28, 35, and 39 (n = 10). The flexural strength was evaluated using the three-point bending test (n = 10). After the period of measurement of fluoride release, seven specimens (n = 7) from each group were randomly selected to evaluate surface roughness using AFM and one specimen was randomly selected for the SEM and EDS analyses. Data were analyzed with two-way ANOVA and Tukey tests (p = 0.05). The irradiation significantly increased fluoride release and surface roughness for Amalgomer CR and Zirconomer groups (p < 0.05). No significant change in flexural strength of the materials was observed after irradiation (p > 0.05). The ionizing radiation altered the amount of fluoride release and surface roughness of only Amalgomer CR and Zirconomer. The effect could be related to the chemical compositions of materials.
The aim of the study was to investigate the effect of different repair procedures on the repair bond strength of bulk-fill and nanohybrid resin composites after different aging periods. The resin composite blocks (8 × 8 × 4 mm3) were prepared from a bulk-fill (reliaFIL Bulk) and a nanohybrid (reliaFIL LC) resin composite and grouped according to aging duration (6 months, 1 year, and 2 years). Following aging, the blocks were assigned to different surface treatments; air-abrasion with aluminum oxide powder, roughening with a diamond bur, and no treatment. After cleansing with phosphoric acid, a silane layer (Porcelain Primer) was applied on the surface of half of the specimens in each group. The specimens were subdivided into two groups (n = 5): Scotchbond Universal (3M Oral Care) and All-Bond Universal (Bisco). The blocks were repaired with the nanohybrid composite (8 × 8 × 8 mm 3). The repaired specimens were stored in distilled water (37 °C/24 h) and segmented into beams. Half of the beams were immediately subjected to microtensile μTBS testing (1 mm/min), while the other half was stored in distilled water (37 °C) for 6 months before testing. Failure modes were analyzed using stereomicroscope and SEM. Statistical analyses were performed with ANOVA and least significant difference tests (LSD) tests (p = 0.05). The extension of aging periods (6 months, 1 year, and 2 years) reduced the repair bond strength in some groups for both resin composites (p < 0.05). The air-abrasion and bur roughening improved the repair bond strength (p < 0.05). The silane application did not influence the repair bond strength and durability (p > 0.05). There was no difference among the universal adhesives in the same surface treatment groups (p > 0.05). The mechanical roughening treatments are necessary for the repair of resin composite. The universal adhesives might be used for the repair of resin composites regardless of silane content without prior silane application.