Welding is one of the most important manufacturing and repair method of today's technology. Though it is known that it can reduced the mechanical properties of materials, it is a necessity in many areas and in some cases, it is preferred because of the efficient and fast manufacturing. The widespread use of welding has raised the problem of reliability of welded structure. It is important to carry on reliability analysis especially on critical welded constructions or some critical materials. In this study, two steel material (AISI 1020 and AISI 6150) which different weldability levels were selected. Gas metal arc welding (GMAW), Gas Tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) were chosen as widespread industrial welding techniques. Welded and non-welded mechanical properties of these materials were examined taking into consideration the reliability, and effect of welding and welding methods were investigated. Reliability analyzes revealed that non-predictable mechanical properties and microstructures are main characteristic of welding process especially in some materials or methods.
The study investigates fatigue failure, a common phenomenon in machine elements subjected to cyclic stresses. The analysis emphasizes that the actual stress experienced by materials often falls below their tensile and yield strengths due to repetitive variable stresses, leading to fatigue damage. Fatigue life is measured by the number of cycles endured before failure. This paper focuses on the aluminum alloy of AlSi10MgMn, extensively used in manufacturing due to its strength, low density, and corrosion resistance. Experimental procedures encompassed tensile testing, microstructural examination, SEM analysis, and fatigue testing. Tensile tests provided initial stress values for fatigue testing. Microstructure analyses verified that heat-treated samples exhibited precipitates. SEM analysis disclosed microstructural characteristics, while fracture surface examinations demonstrated higher fatigue resistance in heat-treated specimens. Hardness measurements were conducted, with heat-treated samples showing higher values. Theoretical calculations based on stress and cycle numbers were compared to experimental fatigue results. The derived equations aligned well with the tests. Ultimately, the study underlines the importance of heat treatment on material behavior and fatigue resistance, shedding light on alloy performance and durability enhancement.
24 April 2019 in Transactions of the Indian Institute of Metals
Industrial washing and drying machines are systems that operate in high-temperature and humid environments, which can therefore be considered aggressive in terms of corrosion. Stainless steel materials to be used in the body structures of these systems are the most important solution in this regard due to their superior corrosion resistance properties. However, due to the low initial investment cost, structural steels, especially from the non-alloy steel group with low carbon content, are widely used in the sector as an alternative to stainless steel in machine and system bodies by increasing the corrosion resistance by applying paint. However, it is an important necessity to apply some additional surface treatments to low carbon steel to supply protection against aggressive corrosive environments. Phosphate coating by spraying is a widely applied industrial method to increase the adhesion of metal surfaces to paint and their resistance to corrosion. A corrosion reaction occurs on the metal surface, which has the ability to react with an acidic phosphate coating solution. Subsequently, the pH rise occurs as a result of neutralization in the region of the solution close to the metal surface. The soluble phosphate form becomes insoluble in the rising pH region, and phosphate coating begins because of crystallization. This etching and coating process continues until the entire surface is covered with a phosphate layer. The coating process ends with the etching reaction as soon as the phosphating solution no longer has direct contact with the metal surface. Within the scope of this study, the corrosion behaviors of two different stainless-steel materials (AISI 304 and AISI 316 ) and a St-37 (S235JR) structural steel material, which was painted directly, painted after phosphate coated and painted+phosphate coated were examined. The aim of the study is to reveal the substitutability of structural steel material to stainless steel materials in terms of corrosion properties. Contact angle measurements, cross-cut test, microhardness and surface roughness value of the samples were analyzed. The lowest corrosion resistance was obtained with phosphate coated, while the highest corrosion resistance was observed in the phosphate coated+painted sample.
30 June 2017 in Celal Bayar Üniversitesi Fen Bilimleri Dergisi
Toz Metal parçaların üretiminin en önemli işlem basamaklarından biri sinterlemedir. Sinterleme aynı zamanda önemli derecede enerji ve zaman tüketiminin olduğu bir ısıl işlemdir. Bu çalışmada ana amaç, aynı dayanım değerleri hedeflenerek, indüksiyon ile sinterleme işlemi vasıtası ile sinterleme sıcaklığının düşürülmesidir. Çalışmada, toz metal numunelerin üretiminde, % 3 Cu, % 0,5 Grafit içeren demir tozu kullanılmıştır. İndüksiyon ile sinterlemenin etkilerinin anlaşılması amacı ile numuneler geleneksel olarak sinterlenerek, üretilen numunelerin mekanik özellikleri ve mikro yapıları karşılaştırılmıştır. Yapılan çalışmalar sonucunda, daha az sürede daha düşük sıcaklıklarda geleneksel sinterlemeye göre daha iyi mekanik özellik değerleri elde edilmiştir.