Precise indoor localization is a major challenge in the field of localization. In this work we investigate multiple error corrections for the ultra-wideband (UWB) technology, in particular the DecaWave DW1000 transceiver. Both the time-of-arrival (TOA) and the time-difference-of-arrival (TDOA) methods are considered. Various clock-drift correction methods for TOA from the literature are reviewed and compared experimentally. The best performing method is extended to TDOA, corrections for the signal power dependence and the hardware delay are added, and two additional enhancements suggested. These are compared to each other and to TOA in positioning experiments.

The position accuracy based on Decawave Ultra-Wideband (UWB) is affected mainly by three factors: hardware delays, clock drift, and signal power. This article discusses the last two factors. The general approach to clock drift correction uses the phase-locked loop (PLL) integrator, which we show is subject to signal power variations, and therefore, is less suitable for clock drift correction. The general approach to the estimation of signal power correction curves requires additional measurement equipment. This article presents a new method for obtaining the curve without additional hardware and clock drift correction without the PLL integrator. Both correction methods were fused together to improve two-way ranging (TWR).

Single visual object tracking from an unmanned aerial vehicle (UAV) poses fundamental challenges such as object occlusion, small-scale objects, background clutter, and abrupt camera motion. To tackle these difficulties, we propose to integrate the 3D structure of the observed scene into a detection-by-tracking algorithm. We introduce a pipeline that combines a model-free visual object tracker, a sparse 3D reconstruction, and a state estimator. The 3D reconstruction of the scene is computed with an image-based Structure-from-Motion (SfM) component that enables us to leverage a state estimator in the corresponding 3D scene during tracking. By representing the position of the target in 3D space rather than in image space, we stabilize the tracking during ego-motion and improve the handling of occlusions, background clutter, and small-scale objects. We evaluated our approach on prototypical image sequences, captured from a UAV with low-altitude oblique views. For this purpose, we adapted an existing dataset for visual object tracking and reconstructed the observed scene in 3D. The experimental results demonstrate that the proposed approach outperforms methods using plain visual cues as well as approaches leveraging image-space-based state estimations. We believe that our approach can be beneficial for traffic monitoring, video surveillance, and navigation.

In the field of indoor localization, ultra-wideband (UWB) technology is no longer dispensable. The market demands that the UWB hardware has to be cheap, precise and accurate. These requirements lead to the popularity of the DecaWave UWB system. The great majority of the publications about this system deals with the correction of the signal power, hardware delay or clock drift. It has traditionally been assumed that this error only appears at the beginning of the operation and is caused by the warm-up process of the crystal. In this article, we show that the warm-up error is influenced by the same error source as the signal power. To our knowledge, no scientific publication has explicitly examined the warm-up error before. This work aims to close this gap and, moreover, to present a solution which does not require any external measuring equipment and only has to be carried out once. It is shown that the empirically obtained warm-up correction curve increases the accuracy for the twoway- ranging (TWR) significantly.

The time-difference-of-arrival (TDOA) self-calibration is an important topic for many applications, such as indoor navigation. One of the most common methods is to perform nonlinear optimization. Unfortunately, optimization often gets stuck in a local minimum. Here, we propose a method of dimension lifting by adding an additional variable into the $l^2$ norm of the objective function. Next to the usual numerical optimization, a partially-analytical method is suggested, which overdetermines the system of equations proportionally to the number of measurements. The effect of dimension lifting on the TDOA self-calibration is verified by experiments with synthetic and real measurements. In both cases, self-calibration is performed for two very common and often combined localization systems, the DecaWave Ultra-Wideband (UWB) and the Abatec Local Position Measurement (LPM) system. The results show that our approach significantly reduces the risk of becoming trapped in a local minimum.