In this paper, a state estimation method of distributed electric drive articulated vehicle dynamics parameters based on the forgetting factor unscented Kalman filter with singular value decomposition (SVD-UKF) is proposed. The 7DOF nonlinear dynamics model of a distributed electric drive articulated vehicle is established. The unscented Kalman filter algorithm is the foundation, with singular value decomposition replacing the Cholesky decomposition. A forgetting factor is introduced to dynamically adapt the observation noise covariance matrix in real time, resulting in a centralized parameter state estimator for the articulated vehicle. The proposed parameter state estimation method based on the forgetting factor SVD-UKF is simulated and compared with the unscented Kalman filter (UKF) estimation method. Key dynamic parameters are estimated, such as the lateral and longitudinal velocities and accelerations, angular velocity, articulated angle, wheel speeds, and longitudinal and lateral tire forces of both the front and rear vehicle bodies. The results show that the proposed forgetting factor SVD-UKF method outperforms the traditional UKF method. Furthermore, a prototype vehicle test is conducted to compare the estimated values of various dynamic parameters with the actual values, demonstrating minimal errors. This verifies the effectiveness of the proposed dynamic parameter estimation method for articulated vehicles.

Passive rehabilitation training in the early poststroke period can promote the reshaping of the nervous system. The trajectory should integrate the physicians’ experience and the patient’s characteristics. And the training should have high accuracy on the premise of safety. Therefore, trajectory customization, optimization, and tracking control algorithms are conducted based on a new upper limb rehabilitation robot. First, joint friction and initial load were identified and compensated. The admittance algorithm was used to realize the trajectory customization. Second, the improved butterfly optimization algorithm (BOA) was used to optimize the nonuniform rational B-spline fitting curve (NURBS). Then, a variable gain control strategy is designed, which enables the robot to track the trajectory well with small human–robot interaction (HRI) forces and to comply with a large HRI force to ensure safety. Regarding the return motion, an error subdivision method is designed to slow the return movement. The results showed that the customization force is less than 6 N. The trajectory tracking error is within 12 mm without a large HRI force. The control gain starts to decrease in 0.5 s periods while there is a large HRI force, thereby improving safety. With the decrease in HRI force, the real position can return to the desired trajectory slowly, which makes the patient feel comfortable.

For patients with upper limb dysfunction after stroke, robot-assisted rehabilitation training plays an important role in functional recovery. The existing upper limb rehabilitation robots have some problems, such as complex mechanisms, insufficient compliance, and can only realize the rehabilitation training of shoulder and elbow joints in the horizontal plane. This research proposes a novel end-effector upper limb rehabilitation robot with three degrees of freedom. Two horizontal rotation freedoms are driven by motors and one vertical translation freedom is driven by a pneumatic cylinder. So it can realize the spatial rehabilitation training of shoulder and elbow joints. The rotation and translation transformation of the robot can be represented by a dual quaternion, which is concise in form and clear in the physical meaning. Therefore, this article adopts dual quaternions to complete the robot’s kinematics modeling, inverse kinematics calculation, and terminal spiral motion trajectory planning. To improve the low-speed moving performance of the spiral motion, a sliding mode control strategy plus feedforward compensation is employed to control the displacement of the cylinder. Experiments show that the robot can realize proximal joints training and has good position tracking accuracy (tracking error is within 2 mm) with smoothness under the proposed control strategy, which can guarantee the accuracy and comfort of passive rehabilitation training, contributing to restoring the function of the impairment upper limbs.

​​​​​​​The integration of virtual reality (VR) technology with rehabilitation robots significantly improves rehabilitation training effectiveness. Although most studies employ VR games to engage patients, few explore activities of daily living (ADL) that incorporate visual, auditory, and force feedback. This article discusses the use of Unity software and a 4-degree-of-freedom upper-limb rehabilitation robot to design a picking and placing training exercise that provides a sense of presence. An inverse kinematics algorithm creates a virtual character to simulate realistic actions and perspective changes. Encouraging prompts and sounds motivate patients, while initial load and friction compensation renders the robot transparent. Virtual objects are assigned different masses, transmitted via the User Datagram Protocol (UDP) and converted into air pressure, allowing a cylinder to generate downward force, simulating gravity. Upper-limb electromyography (EMG) signals are collected during training. The experiment results show that air pressure increases within 1 s to provide a sensation of gravity. Picking up various objects generates distinct EMG signals, with amplitude and variation comparable to dumbbell experiments. This suggests that the proposed ADL training effectively exercises the joints and muscles of the upper extremities, providing high realism in vision and force perception.