The clays of the Zhanjiang Formation in the coastal area of Beibu Gulf of China are thixotropic, and the existing constitutive relationship models relevant for clay are incapable of accurately simulating their stress–strain relationships. It is vital to study the changes of mechanical properties of Zhanjiang Formation clay that occur during thixotropy, and to establish a constitutive model considering thixotropy. The varying measures of its shear strength, cohesion, internal friction angle, and initial tangential modulus during thixotropy were investigated by means of triaxial consolidation and drainage tests. Furthermore, the quantitative relationships between the clay’s cohesion, internal friction angle, and initial tangential modulus of the clay and time were examined. This relationship was introduced into the Duncan–Chang model, and a Duncan–Chang model considering the thixotropy of clay was developed. The established model was used to make predictions to assume the validation of the experimental data, and numerical simulations were then carried out. All of the results from the model’s prediction, numerical simulation and experimental measurements were compared against each other in order to verify the reasonableness of the model we had utilized. The results positively demonstrated that: (1) the shear strength, cohesion, angle of internal friction, and initial tangent modulus of the clay gradually increases with longer curing times, and eventually it will stabilize; and (2) compared with the Duncan–Chang model not considering thixotropy, the established thixotropic model is better able to reflect the influence of clay thixotropy on the clay stress–strain relationship, as its mean relative error is smaller. The results of this study provide references for calculating strength and deformation of the clay thixotropy. Further, it also provides references for bearing load calculations of pile foundations in thixotropic clay strata when subjected to long-term loading conditions.
In the treatment of soda-residue-stabilized soil with high water content using drainage boards with vacuum preloading, the boards often prone to clogging and bending under lateral pressure, reducing their hydraulic conductivity and affecting the soil reinforcement. In this study, the structure of the standard plastic drainage board (filter membrane + filter core) was improved, and three types of new anti-clogging plastic drainage boards with different structures were developed (Type X: geotextile + filter core, Type Y: geotextile + wire mesh + filter core, Type Z: geotextile + filter membrane + filter core). Permeability tests were subsequently used to determine the optimal structure. In-lab vertical draining tests with vacuum preloading were carried out on the selected model to study the change in water content, vacuum pressure, surface settlement, vane shear strength, and pore water pressure of soil with drainage board insertion depth, providing a reference for the application of new anti-clogging drainage boards in engineering. The results showed that: (1) the type Y anti-clogging plastic drainage board (geotextile + wire mesh + filter core) exhibits the most balanced performance in terms of permeability, anti-clogging ability, tensile strength and bending strength and is suitable for vacuum preloading of soda residue with high water content; (2) the mechanical properties and anti-clogging performance of drainage boards are highly dependent on their structural configuration. Introducing a wire mesh between the filter core and the geotextile significantly enhances the tensile and bending strength of the drainage board without noticeably compromising its drainage performance; (3) the insertion depth of the drainage board significantly affects drainage efficiency, vacuum transmission rate, and strength development of the soda residue. The effective reinforcement range of the drainage board is not limited to the insertion depth but also extends below the bottom of the drainage board.
As the economy evolves, there has been an increasing interest in exploring oceanic resources. However, the complex marine environment poses several geological challenges for offshore engineering endeavors. The presence of gassy soil significantly influences the deformation properties and integrity of the soil, significantly impacting offshore engineering construction. Triaxial shear tests and creep tests were conducted on gassy clay with silt content, prepared using the laboratory “zeolite method”, to analyze its shear deformation characteristics and long-term resilience. We proposed a prediction model for calculating the long-term resilience of silt-containing clay, accounting for confining pressure and gas content, and verified its efficacy through experimentation. Our findings reveal the following: The stress–strain relationship curve of silt-containing gassy clay is a typical strain hardening curve. The greater the confining pressure or the smaller the gas content, the greater the stress under the same strain and the greater the yield stress; when the gas content is the same, the greater the confining pressure, the greater the long-term strength of the soil; and when the confining pressure is the same, the smaller the gas content, the greater the long-term strength of the soil. The research results can provide theoretical reference for actual complex engineering.