Since the sixties, most of numerical studies that model the rotary lip seal lubrication have been restricted by assuming that one of the two opposing surfaces is smooth: either the lip or the shaft. This hypothesis, although it is verified only for a shaft roughness ten times smaller than that of the seal, is the best solution to avoid the transient term “∂h/∂t” in the deterministic approach. Thus, the subject of the present study is twofold. The first part validates the current hydrodynamic model with the international literature by assuming the asperities on the lip and shaft as a two-dimensional cosine function. In the second part the Reynolds equation for rough surfaces with relative motion is solved. The numerical results show that the relative motion between rough surfaces impacts significantly the load support and the leakage rate, but affects slightly the friction torque.

Recent research has focused on energy recovery and storage technologies. One of the materials allowing the recovery of dissipated energy is the piezoelectric material (PE). These functional materials perform reversible energy conversion, transforming electrical energy into mechanical and vice versa. In this study, we investigate the recovery of vibratory energy in vehicle suspension systems—energy traditionally dissipated by conventional shock absorbers—using piezoelectric materials to capture this wasted energy and redirect it to the vehicle’s auxiliary power supply network. We propose an integrated electromechanical model incorporating piezoelectric actuators in parallel with the suspension mechanism. The collected energy is processed and stored for later use in powering accessories such as windows and mirrors. The idea is to integrate renewable energy sources to optimize the performance of the vehicle. We proposed a Multiphysics model of the system under a software used to this type of modeling (Simcenter AMESim v1610_student). The simulation results of the system and its various sub-systems are presented for studying the piezo-actuator response to reduce consumption and increase energy performance in a vehicle. These findings will undergo experimental validation in the project’s subsequent phase.

In the last years, the new research papers piezoelectric energy harvesting from vortex-induced vibration (PEH-VIV) are focused on indirect contact between airflow and piezoelectric transducer. Where some researchers have noticed that is difficult to establish an accurate analytical model that could describe precisely the behavior of the piezoelectric generator including the indirect interaction with airflow. Due to these difficulties, new studies are concentrating directly on the experimental investigations to get results of energy harvesters of the indirect-contact piezoelectric wind energy harvesters (IC-PWEHs). However, this paper presents an analytical model that can provide good results according to experimental tests. The obtained results concern the displacement of the piezoelectric transducer indirectly excited by a vortex-induced vibration (VIV) and the generated voltage according to a different mass of cylindrical shell. The numerical results of the model show a significant agreement with the experimental results due to the good estimation of the system’s parameters, where the computing is done numerically using the MATLAB Simulink. Additionally, the optimal mass value of the piezoelectric transducer was determined approximately by the proposed analytical model. Where this mass is equivalent to the highest voltage amplitude according to the experimental tests.

This research examines the feasibility of recovering and recycling condensate water, a waste byproduct generated by Atlas Copco ZR315 FF industrial air compressors utilizing oil-free rotary screw technology with integrated dryers. Given the growing severity of global water scarcity, finding alternative water sources is essential for sustainable industrial practices. This study specifically evaluates the potential of capturing and treating compressed air condensate as a viable method for water recovery. The investigation analyzes both the quantity and quality of condensate water produced by the ZR315 FF unit. It contrasts this recovery approach with traditional water production methods, such as desalination and atmospheric water generation (AWG) via dehumidification. The findings demonstrate that recovering condensate water from industrial air compressors is a cost-effective and energy-efficient substitute for conventional water production, especially in water-stressed areas like Morocco. The results show a significant opportunity to reduce industrial water usage and provide a sustainable source of process water. This research therefore supports the application of circular economy principles in industrial water management and offers practical solutions for overcoming water scarcity challenges within manufacturing environments.

This research examines the feasibility of recovering and recycling condensate water, a waste byproduct generated by Atlas Copco ZR315 FF industrial air compressors utilizing oil-free rotary screw technology with integrated dryers. Given the growing severity of global water scarcity, finding alternative water sources is essential for sustainable industrial practices. This study specifically evaluates the potential of capturing and treating compressed air condensate as a viable method for water recovery. The investigation analyzes both the quantity and quality of condensate water produced by the ZR315 FF unit. It contrasts this recovery approach with traditional water production methods, such as desalination and atmospheric water generation (AWG) via dehumidification. The findings demonstrate that recovering condensate water from industrial air compressors is a cost-effective and energy-efficient substitute for conventional water production, especially in water-stressed areas like Morocco. The results show a significant opportunity to reduce industrial water usage and provide a sustainable source of process water. This research therefore supports the application of circular economy principles in industrial water management and offers practical solutions for overcoming water scarcity challenges within manufacturing environments.