The classic S-plane control method combines PD structure with fuzzy control theory, with the advantages of a simple control structure and fewer parameters to be adjusted. It has been proved as a practical method in an autonomous underwater vehicle (AUV) motion control at low and medium speeds, but it takes no account of the situational static load and varying hydrodynamic forces which influence the control quality and even result in a “dolphin effect” at the time of high-speed movement. For this reason, an improved S-plane controller is designed based on the sliding mode variable structure, sliding mode surface, and control items in order to respond to the situational static load and high-speed movement. The improved S-plane controller is verified by Lyapunov stability analysis. The thrust allocation strategies are also discussed with constraints introduced in accordance with task requirements. In order to verify the practicability and effectiveness of the improved S-plane controller, both simulation experiments and field trials of AUV motion control, long-range cruise, and path point following were carried out. The results have demonstrated the superiority of the improved S-plane controller over the classic S-plane controller.

In view of the requirements on control precision of autonomous underwater vehicles (AUVs) in different operations, the improvement of AUV motion control accuracy is the focus of this paper. In regard to the unsatisfying robustness of traditional control methods, an interactive network based on Least Square Support Vector Regression (LSSVR) is therefore put forward. The network completed the identification of the strong nonlinear AUV dynamic characteristics based on the LSSVR theory and by virtue of the interactions between the offline and online modules, it achieved offline design and online optimization of the AUV control law. In addition to contrastive numerical simulations and sea trials with the classic S-plane method in AUV velocity and heading control, the LSSVR network was also tested in path following and long-range cruise. The precision and robustness and of the proposed network were verified by the high-accuracy control results of the aforesaid simulations and trials. The network can be of practical use in AUV control especially under unfamiliar water conditions with access to a limited number of control samples or little information of the operation site.

Intelligent underwater vehicles hover by way of a hovering control system. To provide design inputs and maneuver guidance, this study focused on the characteristics of intelligent underwater vehicles during hovering control with the propulsion system shut down, established a mathematical model of hovering control and determined injection and drainage functions based on optimal control theory. From analysis simulation experiments, the influence laws of control parameters, control timing and rate of injection and drainage control upon hovering control were deduced. It is proposed that, at the time of control parameter selection, the continuous injection and drainage rate at each time should be reduced as far as possible to relieve the demand on the volume of the reservoir when the requirement of depth control accuracy has been satisfied. In addition, the injection and drainage control should initiate when depth changes exceed 0.5 m. Suggestions are included on the minimum injection and drainage rate required for different initial disturbances. The proposed suggestions guide the design of hovering control systems and hovering control over intelligent underwater vehicles.

A six degree-of-freedom (DOF) motion control system for docking with a deep submergence rescue vehicle (DSRV) test platform was the focus of this study. The existing control methods can meet the general requirements of underwater operations, but the complex structures or multiple parameters of some methods have prevented them from widespread use. The majority of the existing methods assume the heeling effect to be negligible and ignore it, achieving motion control in only four or five DOFs. In view of the demanding requirements regarding positions and inclinations in six DOFs during the docking process, the software and hardware architectures of the DSRV platform were constructed, and then sparse filtering technology was introduced for data smoothing. Based on the adaptive control strategy and with a consideration of residual static loads, an improved S-plane control method was developed. By converting the force (moment) calculated by the controller to the body coordinate system, the complexity of thrust allocation was effectively reduced, and the challenge of thrust allocation in the case of a high inclination during dynamic positioning was solved accordingly. The automatic control of the trimming angle and heeling angle was realized with the linkage system of the ballast tank and pump valve. A PID method based on an intelligent integral was proposed, which not only dealt with the integral “saturation” problem, but also reduced the steady-state error and overshooting. Water pool experiments and sea trials were carried out in the presence of water currents for six-DOF motion control. The responsiveness and precision of the control system were verified by the pool experiment and sea trial results and could meet the control requirements in engineering practice. The reliability and operational stability of the proposed control system were also verified in a long-distance cruise.

The issue of dynamic event-triggered trajectory tracking control of autonomous underwater vehicles (AUVs) in the Trans-Atlantic Geotraverse (TAG) active mound is addressed. Concretely, a novel adaptive event-triggered disturbance observer along with auxiliary functions is constructed to handle with actuator faults and ocean current in the TAG active mound. By using rotation matrices, a new tracking error system involving position and attitude is developed such that potential singularities caused by the large pitch will be sufficiently avoided. By deep combination with model parameters, a sliding mode manifold based on additional velocity errors is established to promote robustness and convergence. Following the detailed analysis, sufficient conditions for the input-to-state practical stability in mean square are given to ensure the tracking performance. An adaptive dynamic event-trigger method is applied to reduce the communication frequency between the embedded PC module and actuators. Finally, the applications of an AUV tracking system in the near-bottom hydrothermal mound are carried out to verify the efficiency of the presented method.