The dramatic reduction in power consumption of current integrated circuits has evoked great research interests in harvesting ambient energy, such as vibrations, as a potential power supply for electronic devices to avoid battery replacement. Currently, most vibration-based energy harvesters are designed as linear resonators to achieve optimal performance by matching their resonance frequencies with the ambient excitation frequencies a priori. However, a slight shift of the excitation frequency will cause a dramatic reduction in performance. Unfortunately, in the vast majority of practical cases, the ambient vibrations are frequency-varying or totally random with energy distributed over a wide frequency spectrum. Hence, developing techniques to increase the bandwidth of vibration-based energy harvesters has become the next important problem in energy harvesting. This article reviews the advances made in the past few years on this issue. The broadband vibration-based energy harvesting solutions, covering resonance tuning, multimodal energy harvesting, frequency up-conversion, and techniques exploiting non-linear oscillations, are summarized in detail with regard to their merits and applicability in different circumstances.

This letter proposes a magnetic coupled piezoelectric energy harvester (PEH), in which the magnetic interaction is introduced by a magnetic oscillator. For comparison purpose, lumped parameter models are established for the conventional linear PEH, the nonlinear PEH with a fixed magnet, and the proposed PEH with a magnetic oscillator. Both experiment and simulation show the benefits from the dynamics of the magnetic oscillator. In the experiment, nearly 100% increase in the operating bandwidth and 41% increase in the magnitude of the power output are achieved at an excitation level of 2 m/s².

This letter presents a comparative study of different tip cross-sections for small scale wind energy harvesting based on galloping phenomenon. A prototype device is fabricated with a piezoelectric cantilever and a tip body with various cross-section profiles (square, rectangle, triangle, and D-shape) and tested in a wind tunnel. Experimental results demonstrate the superiority of the square-sectioned tip for the low cut-in wind speed of 2.5 m/s and the high peak power of 8.4 mW. An analytical model is established and verified by the experimental results. It is recommended that the square section should be used for small wind galloping energy harvesters.

Last decade has seen growing research interest in vibration energy harvesting using piezoelectric materials. When developing piezoelectric energy harvesting systems, it is advantageous to establish certain analytical or numerical model to predict the system performance. In the last few years, researchers from mechanical engineering established distributed models for energy harvester but simplified the energy harvesting circuit in the analytical derivation. While, researchers from electrical engineering concerned the modeling of practical energy harvesting circuit but tended to simplify the structural and mechanical conditions. The challenges for accurate modeling of such electromechanical coupling systems remain when complicated mechanical conditions and practical energy harvesting circuit are considered in system design. In this article, the aforementioned problem is addressed by employing an equivalent circuit model, which bridges structural modeling and electrical simulation. First, the parameters in the equivalent circuit model are identified from theoretical analysis and finite element analysis for simple and complex structures, respectively. Subsequently, the equivalent circuit model considering multiple modes of the system is established and simulated in the SPICE software. Two validation examples are given to verify the accuracy of the proposed method, and one further example illustrates its capability of dealing with complicated structures and non-linear circuits.

Energy harvesting from ambient vibrations using piezoelectric effect is a promising alternative solution for powering small electronics such as wireless sensors. A conventional piezoelectric energy harvester usually consists of a cantilevered beam with a proof mass at its free end. For such a device, the second resonance of the piezoelectric energy harvester is usually ignored because of its high frequency as well as low response level compared to the first resonance. Hence, only the first mode has been frequently exploited for energy harvesting in the reported literature. In this article, a novel compact piezoelectric energy harvester using two vibration modes has been developed. The harvester comprises one main cantilever beam and an inner secondary cantilever beam, each of which is bonded with piezoelectric transducers. By varying the proof masses, the first two resonant frequencies of the harvester can be tuned close enough to achieve useful wide bandwidth. Meanwhile, this compact design efficiently utilizes the cantilever beam by generating significant power output from both the main and secondary beams. An experiment and simulation were carried out to validate the design concept. The results show that the proposed novel piezoelectric energy harvester is more adaptive and functional in practical vibrational circumstances.