Murtada Abass A Alrubaie

Murtada Abass A Alrubaie


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 January 2019 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
MURTADA ALRUBAIEMURTADA ALRUBAIE
MURTADA ALRUBAIE
RLRoberto A Lopez-Anido
Roberto A Lopez-Anido
DGDouglas J Gardner
Douglas J Gardner
MTMehdi Tajvidi
Mehdi Tajvidi
YHYousoo Han
Yousoo Han
The hygrothermal effect on the short-term creep behavior of extruded thermally modified wood fiber–high-strength styrenic copolymer plastic composites (wood–plastic composites (WPCs)) was investigated on specimens preconditioned for 1 month under water immersion (distilled water (DW) and saltwater (SW)). These specimens were then tested in the same conditions for short-term creep and creep-recovery response using a submersible clamp. The short-term creep tests of WPC specimens (that are immersed in water as a function of different temperatures) have not yet been reported in previous studies. The objective of this study was to determine whether the hygrothermal creep response of WPC material evaluated through water immersion differs from the creep response published in the literature for other environmental exposure conditions. The experiments included measuring 30 min of creep and 30 min of creep recovery on the specimens immersed in SW and DW at two different levels of flexural stresses (9% and 14% of the flexural strength) and three temperature values (25, 35, and 45°C). The average creep strain recovery (%) of the specimens was higher for the specimens immersed in SW during testing than the control specimens. The WPC material is considered to have a potential use in structural applications in environments where the temperature is below 45°C because of the following factors: the low deformation under the short-term sustained loading, the decrease in the deformation rate with respect to the increase in load duration, maintaining the modulus of elasticity over a range of temperatures from 25°C to 45°C under sustained load, and the ability to recover more than 69% of the average creep strain under water immersion when the loading source is removed. The creep strain fractional increment (CSFI) of the WPC in this study under all conditions was 13% which is 86% lower than the CSFI of the WPCs reported in previous studies.
1

24 January 2020 in Polymers
Verified
Journal Article
Open access
PDF file
MURTADA ALRUBAIEMURTADA ALRUBAIE
MURTADA ALRUBAIE
Roberto A Lopez-AnidoRoberto A Lopez-Anido
Roberto A Lopez-Anido
DGDouglas Gardner
Douglas Gardner
The use of wood plastic composite lumber as a structural member material in marine applications is challenging due to the tendency of wood plastic composites (WPCs) to creep and absorb water. A novel patent-pending WPC formulation that combines a thermally modified wood flour (as a cellulosic material) and a high strength styrenic copolymer (high impact polystyrene and styrene maleic anhydride) have been developed with advantageous viscoelastic properties (low initial creep compliance and creep rate) compared with the conventional WPCs. In this study, the creep behavior of the WPC and high-density polyethylene (HDPE) lumber in flexure was characterized and compared. Three sample groupings of WPC and HDPE lumber were subjected to three levels of creep stress; 7.5, 15, and 30% of the ultimate flexural strength (Fb) for a duration of 180 days. Because of the relatively low initial creep compliance of the WPC specimens (five times less) compared with the initial creep compliance of HDPE specimens, the creep deformation of HDPE specimens was six times higher than the creep deformation of WPC specimens at the 30% creep stress level. A Power Law model predicted that the strain (3%) to failure in the HDPE lumber would occur in 1.5 years at 30% Fb flexural stress while the predicted strain (1%) failure for the WPC lumber would occur in 150 years. The findings of this study suggest using the WPC lumber in structural application to replace the HDPE lumber in flexure attributable to the low time-dependent deformation when the applied stress value is withing the linear region of the stress-strain relationship.

3 November 2022 in BioResources
Verified
Journal Article
Closed access
MURTADA ALRUBAIEMURTADA ALRUBAIE
MURTADA ALRUBAIE
SWSalam Wtaife
Salam Wtaife
ZAZahraa Hussein Joudah Alsafy
Zahraa Hussein Joudah Alsafy
NKNur Hafizah Abd Khalid
Nur Hafizah Abd Khalid
The effect of replacing the conventional coarse aggregate with wood shavings was evaluated relative to the 28-day compressive strength of the concrete. Six groups were studied: group-1 represented the normal concrete (NC-CTRL1), group-2 (TW-CTRL2) comprised the specimens that had the replacement of the coarse aggregate with raw wood shavings, group-3, group-4, group-5, and group 6 represented the specimens that had the coarse aggregate as coated (treated) wood shavings with cement paste (group-3 and -4) and with tile adhesive paste (group-5 and -6), with and without the effect of the emulsifier, respectively. The density of the TW-CTRL2 concrete was 31.4% lighter than NC-CTRL1. However, the compressive strength of TW-CTRL2 was 75% of the NC-CTRL1, but within the acceptable limits stated in ASTM standards. The findings of this study showed a potential to use the produced concrete as concrete masonry unit when compared with the values reported in previous studies. Compared with TW-CTRL2, the compressive strength increased 45% and 20% for the coated wood shavings with cement and tile adhesive pastes, respectively. The effect of using the emulsifier in the coating process of the wood shavings increased the compressive strength by 20%, and reduced the voids of the concrete by 3%.

21 July 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MURTADA ALRUBAIEMURTADA ALRUBAIE
MURTADA ALRUBAIE
DGDouglas Gardner
Douglas Gardner
Roberto A Lopez-AnidoRoberto A Lopez-Anido
Roberto A Lopez-Anido
The long-term deformation of a geodesic spherical frame structure with a diameter of 20 m made from wood plastic composite (WPC) lumber (struts) is described using the Norton-Bailey power law model to predict the service life creep behavior (the creep strain ( ε c r )) of the WPC. The Norton-Bailey power law model parameters, A the power law multiplier, n the stress order, and m the time order, were obtained from experimental four-point bending flexural creep measurements of WPC lumber subjected to three levels of flexural stress: 7, 14, and 29% of the ultimate flexural strength for 200 days. The parameters obtained from the experiments showed good agreement to the model of the WPC lumber in flexure. The Norton-Bailey power law parameters were then implemented to describe the long-term deformation of the spherical frame structure. The limit of failure was considered when the WPC creep strain reaches the value of 1%. However, the FEA predicted the maximum creep strain to be 20% of the failure strain. This modeling approach is considered useful to describe and predict the long-term deformation of aquacultural structures made from viscoelastic materials during the envisioned service life (10 years) based on experimental creep data for the members that form the structure.

9 January 2019 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
MURTADA ALRUBAIEMURTADA ALRUBAIE
MURTADA ALRUBAIE
Roberto A Lopez-AnidoRoberto A Lopez-Anido
Roberto A Lopez-Anido
DGDouglas J Gardner
Douglas J Gardner
MTMehdi Tajvidi
Mehdi Tajvidi
YHYousoo Han
Yousoo Han
The viscoelastic behavior of an extruded wood plastic composite (WPC) made from thermally modified wood under hygrothermal treatment was studied and modeled. Multiple three-point bending creep/recovery tests were carried out using a dynamic mechanical thermal analyzer (DMTA) equipped with a submersible clamp. WPC specimens with a 15-mm span were subjected to two initial applied stresses; 9% and 14% of the flexural strength in 30 min of creep and 30 min of creep recovery under the combined effects of temperature (25°C, 35°C, and 45°C) and water immersion (saltwater (SW) and distilled water). A dry condition WPC control was used to compare the hygrothermal effects with respect to the control conditions. The WPC material in this article exhibited a linear viscoelastic behavior under the effect of temperature, whereas a nonlinear viscoelastic behavior was observed under immersion conditions. A power law model is considered a useful model to describe the creep behavior of WPC specimens with a 15-mm span in the control and the SW conditions and at 45°C. A power law model was used to describe 180-day creep deflection of WPC lumber beams with an 853-mm span subjected to 12 MPa of the flexural strength in four-point bending at 50% relative humidity and at 21°C. The power law model predicts that the WPC lumber will reach a flexural strain in outer fiber of 1% in approximately 150 years.

21 December 2019 in Polymers
Verified
Journal Article
Open access
PDF file
MURTADA ALRUBAIEMURTADA ALRUBAIE
MURTADA ALRUBAIE
DGDouglas Gardner
Douglas Gardner
Roberto A Lopez-AnidoRoberto A Lopez-Anido
Roberto A Lopez-Anido
Based on previous research, a novel wood–plastic composite (WPC) lumber has shown potential to replace high-density polyethylene (HDPE) lumber in the construction of aquacultural geodesic spherical cage structures. Six HDPE and six WPC assemblies, which are representative of typical full-size cage dimensions, were fabricated by bolting pairs of triangular panel components made with connected struts. Half of the panel assemblies had a plastic-coated steel wire mesh to simulate the actual restraint in field applications of the cages. The objective of the research was to characterize the structural performance of the panel assemblies under compressive loading. To determine the critical buckling load for the panel assemblies made from WPC and HDPE struts with and without wire mesh, Southwell’s method was implemented. A two-dimensional (2D) linear finite element analysis model was developed to determine axial forces in the struts of the panel assembly for the applied load and boundary conditions. This model was used to determine strut compressive forces corresponding to the Southwell’s method buckling load and the experimental failure load. It was found that the wire mesh increased the load capacity of both HDPE and WPC panel assemblies by a factor of two. The typical failure mode of the panels made from HDPE lumber struts, with and without wire mesh, was buckling of the struts, whereas the failure mode of the WPC panels, with and without wire mesh, was fracture at the notched section corresponding to the location of the bolts. The load capacity of the panel assemblies made from WPC lumber struts was three times and 2.5 times higher than the load capacity of the panel assemblies made from HDPE lumber struts with and without wire mesh, respectively.