Polyether-ether-ketone (PEEK) exhibits great potential in being a replacement for metal components across various applications relying on the mechanical and tribological properties. However, there is still much to be done to improve its properties. The main motivation of this paper is to improve the tribological and mechanical properties of PEEK simultaneously for more severe working environment. Therefore, dialkyl pentasulfide (RC2540) was proposed to fill into the cavity of CNTs to prepare nano-capsules, which were then filled into PEEK to prepare PEEK/nano-capsules composites. The existence of nano-capsules in PEEK was analyzed, and the friction and wear properties exhibited by PEEK composites against GCr15 steel were examined using pin-disk friction pairs, and the self-lubricating mechanism of PEEK composites in friction was revealed. Findings of this study indicated that when the mass fraction of nano-capsules was less than 5%, the filling of nano-capsules could improve the tensile strength of PEEK and reduced the friction coefficient and specific wear rate of PEEK by filling nano-capsules. During the friction process, RC2540 in the nano-capsules can be released as PEEK wears so that a self-lubricating layer can be formed for reducing PEEK composites’ friction and wear.
Background: Multi-walled carbon nanotubes (MWCNTs) were filled with dialkyl pentasulfide (DPS) to prepare MWCNTs-DPS composite (nanocomposite) additives for used in nanofluid-based machining. Methods: The nanocomposite was prepared by a liquid phase wet chemistry method, and was then added in pure water with surfactant to form the nanofluids. This study comprehensively uncovered the effects of additive concentration, acid treatment time, testing temperature and electrowetting conditions on the electrical conductivity and wettability of the nanofluids. Results: The nanocomposite was successfully produced with a maximum filling rate of 27.4%. Meanwhile, its additives produced an optimal performance at a concentration of about 0.1%. As a result, the electrical conductivity and wettability of the nanofluids increased by more than 13.7% and 6.35%, respectively compared to individual MWCNTs additives. Under the electro-wettability conditions, the wetting performance of the nanofluids produced by the nanocomposite increased with the growth of charging voltage. Moreover, the nanofluids with a higher additive concentration perform better wetting performance due to higher conductivity and greater charge capacity. Conclusion: The modification and filling activate the surface activity, electrical conductivity and capacitance property of the MWCNTs, which arose out of the enhanced performance.
The dialkyl pentasulfide (DPS) – filled carbon nanotubes (CNTs) composites were successfully prepared by liquid phase wet chemistry method. Firstly, the CNTs were truncated with concentrated acid, and the end cap of CNTs was opened after the treatment. Under the liquid phase condition, the DPS was filled in the CNTs through the capillary force. Then, the composition and morphological structure of the samples were characterized by infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), energy dispersive spectrum (EDS) and thermogravimetric analysis (TG/DSC). The results showed that the DPS filled CNTs could be obtained by liquid-phase wet chemistry method. During the filling process, the DPS and the CNTs were mainly physical combinations, and the filling ratio of DPS was about 25%. The DPS was infiltrated into CNTs through a capillary effect and then protected by CNTs after the formation of the composites.
Grinding fluid often struggles to enter the grinding area and overcoming this challenge has been a major focus of research in recent years. Therefore, CNTs@T304 nano-capsules are prepared by filling the cavities of CNTs with a lubricant of T304. CNTs@T304 nano-capsules were used as an additive in this paper to prepare resin grinding wheels and nanofluids, respectively. The resin wheels filled with nano-capsules were used for grinding under the lubrication of nanofluids, and T304 could then be released to the grinding area to play a self-lubricating role during grinding. First, CNTs@T304 nano-capsules were characterized, and the properties of the prepared grinding wheels and nanofluids were tested. Second, the effects of the filling of nano-capsules and grinding speed on the grinding force, grinding temperature, surface roughness, and grinding ratio were studied. Finally, the lubrication mechanism of the nano-capsules was revealed through surface analysis of the workpiece. The results suggested that nano-capsules had good thermal stability and the nanofluid prepared from them exhibited good dispersion stability and thermal conductivity. The grinding wheel was found to satisfy the service conditions when the filling content was less than 15%. Compared with a common wheel, the grinding force and grinding temperature were reduced by 24% and 28%, respectively, and the surface roughness of the workpiece and the grinding ratio were increased by 18% and by 21%, respectively, when grinding GCr15 steel with the nano-capsule wheel. Lubrication with nanofluids could further reduce the grinding force, grinding temperature, and surface roughness values. During grinding, the self-lubrication film formed by the T304 released from the nano-capsules in the wheel served first and foremost as a lubricant. The intervention of the nanofluid enhanced the heat-exchange effect and lubrication efficiency in the grinding zone.