A simple active mode-locked erbium-doped fiber (EDF) ring laser is characterized and experimentally demonstrated. The active mode-locked laser can be tuned in the C-band wavelength range 1525 nm to 1565 nm using a tunable bandpass filter placed in the cavity. An intensity modulator placed inside the laser cavity is driven using a sinusoidal signal at different repetition rates. The laser can produce trains of pulses with a width that is controlled using the mode-locking order. The experiments demonstrated an active mode-locked laser that can generate pulse trains with 39 ns width at multiple cavity fundamental frequency of 0.67 MHz repetition rate. Numerical simulations are conducted to investigate the effect of the tunable filter bandwidth and the power of the EDF 980 nm pump on the mode-locking process and produced pulses width.

The optoelectronic oscillator is a delay line oscillator that leverages optical fibre technology to realize the large delay required for low phase noise systems. Spurious sidemodes are an artefact of the delay line oscillator, yet treatments of injection locking of optoelectronic oscillators have relied on the application of classical injection locking theory valid only for single mode oscillators. The large delay contributed by the optical fibre delay line is accounted for by the classical theory only in part through the quality factor Q that captures the round-trip group delay in a neighborhood of the oscillation frequency. This paper presents a new formulation of time delay oscillators subject to injection that describes all the essential features of their dynamics and phase noise. The common assumptions of a single mode oscillator and weak injection are removed. This is important to correctly predict the lock-in range, the suppression of sidemodes and the phase noise spectrum. The findings of the analysis are validated by experimental measurements provided by an optoelectronic oscillator under injection by an external source.

AlGaAs tunnel junctions are shown to be well-suited to concentrated photovoltaics where temperatures and current densities can be dramatically higher than for 1-sun flat-panel systems. Detailed comparisons of AlGaAs/AlGaAs tunnel junction experimental measurements over a range of temperatures expected during device operation in concentrator systems are presented. Experimental and simulation results are compared in an effort to decouple the tunnel junction from the overall multi-junction solar cell. The tunnel junction resistance is experimentally studied as a function of the temperature to determine its contribution to overall efficiency of the solar cell. The current-voltage behavior of the isolated TJ shows that as the temperature is increased from 25°C to 85°C, the resistance decreases from ~4.7×10^-4 ¿·cm² to ~0.3×10^-4 ¿·cm² for the operational range of a multi-junction solar cell under concentration.

A photonic implementation of a wavelength meter typically applies an interferometer to measure the frequency-dependent phase shift provided by an optical delay line. This work shows that the information to be retrieved is encoded by a vector restricted to a circular cone within a 3D Cartesian object space. The measured data belong to the image of the object space under a linear orthogonal map. Component impairments result in broken orthogonal symmetry, but the mapping remains linear. The circular cone is retained as the object space, which suggests that the conventional conic section fitting for the wavelength meter application is a premature reduction of the object space from R³ to R². The inverse map, constructed by a learning algorithm, compensates impairments such as source intensity fluctuation and errors in delay time, coupler transmission, and photoreceiver sensitivity while being robust to noise. The simple algorithm does not require initial estimates for all parameters except for a broad bracket of the delay; further, weak nonlinearity introduced by uncertain delay can be corrected by a robust golden search algorithm. The phase-retrieval process is invariant to source power and its fluctuation. Simulations demonstrate that, to the extent that the ten parameters of the interferometer model capture all significant impairments, a precision limited only by the level of random noise is attainable. Applied to measured data collected from a fabricated Si₃N₄ wavelength meter, greater than an order of magnitude improvement in precision compared with the conventional method is achieved.

Phase noise reduces target sensitivity in radar and increases bit error rate in telecommunications systems. Optoelectronic oscillators are known for using optical fibre technology to realise the large delay required to attain superior phase noise performance compared to conventional microwave source technology. However, the long fibre is vulnerable to environmentally induced phase perturbations, while conventional phase shifters have insufficient range to compensate for the phase drift over the operational temperature range without the use of a temperature-controlled enclosure. Here we introduce a vector modulator controlled by a Stuart-Landau integrator, as a solution to non-efficient tuning for the phase shift. The concept is verified by simulation and experimentally demonstrated using an optoelectronic oscillator phase-locked to a system reference. Phase lock is maintained over four free spectral ranges equivalent to a tuning phase range of 1440° when the optoelectronic oscillator is cycled over a 10 °C to 85 °C temperature range. These demonstrations highlight the practical potential of our continuous tuning method.

Monitoring the state of the optical network is a key enabler for programmability of network functions, protocols and efficient use of the spectrum. A particular challenge is to provide the SDN-EON controller with a panoramic view of the complete state of the optical spectrum. This paper describes an architecture for compact on-chip spectrometry targeting high resolution across the entire C-band to reliably and accurately measure the spectral profile of WDM signals in fixed and flex-grid architectures. An industry standard software tool is used to validate the performance of the spectrometer. The fabrication of the proposed design is found to be practical.