The effect of temperature on plastic strain and resilient modulus (MR) of different sources of recycled asphalt pavement (RAP) and recycled concrete aggregate (RCA) was evaluated from the results of laboratory temperature-controlled MR tests, with a conventional Class 5 aggregate serving as the control. Freeze–thaw tests were also conducted on samples of RAP and RCA. Five years (spring–summer–fall–winter) of field falling weight deflectometer (FWD) tests were conducted on three pavement sections with RAP, RCA, and Class 5 as the unbound base course. Laboratory test results showed that temperature rise increased plastic strain and reduced MR of RAP under cyclic loads but had a negligible effect on plastic strain and MR of RCA. Freeze–thaw cycles steadily reduced the MR of RAP; however, long-term freeze–thaw cycles increased the MR of RCA. Thermal preloading reduced the plastic strain and increased the MR of the compacted RAP. Construction of a pavement system made with RAP is thus recommended during warm seasons to induce thermal preloading. The elastic modulus back-calculated from the FWD tests did not show a consistent trend with respect to temperature change. No significant change on elastic modulus of RAP, RCA, and Class 5 aggregates due to freeze–thaw cycles was observed over five years.
1 October 2017 in Journal of Materials in Civil Engineering
Properties of raw dredged material (RDM) stabilized with self-cementing Class C fly ash (FA) were evaluated for beneficial use in geotechnical construction applications. Emphasis was placed on evaluating effects of curing time and fly ash content on index and engineering properties relevant to pavement construction. RDM samples were blended with 10, 20, and 30% FA and cured for 2 h, 7 days, and 28 days. Fly ash stabilization reduced plasticity and improved the engineering properties of the stabilized dredged material (SDM). Increasing FA content increased maximum dry unit weight and reduced optimum water content for compaction. Unconfined compressive strength ( ) increased with FA content and curing time. The effect of curing time on was more significant at higher FA content. Freeze-thaw cycles only reduced the strength of SDM specimens by 5% on average, indicating that SDM was durable to freeze-thaw. Analytical relationships were developed to predict Atterberg limits and of SDM at different fly ash contents and curing times. The California bearing ratio (CBR) for the SDM ranged from 10 to 20, which is comparable to compacted silty sand or sand and rates as fair to good for pavement subgrade. The resilient modulus ( ) increased significantly with FA content and varied between 35 and 83 MPa, which is comparable to gravel or crushed stone and rates as good to excellent for subgrade. Results indicate that low-strength dredged materials stabilized with Class C fly ash are viable for beneficial use as pavement subgrade material.
1 January 2013 in Journal of Materials in Civil Engineering
The majority of tear-off roofing shingles and manufacturing shingle scraps are currently disposed of as solid waste in landfills. Landfills are also the end place for the majority of coal combustion byproducts like fly ash. In this study, geotechnical properties of recycled asphalt shingles (RAS) stabilized with a self-cementing fly ash (FA) for use as structural fill material were systematically evaluated. Compaction, hydraulic conductivity, compressibility, shear strength, and coefficient of lateral earth pressure at rest (Ko) of stabilized RAS were evaluated. The maximum dry unit weight (γdmax) of RAS:FA mixtures varies between 11.3 kN/m3 and 13.8 kN/m3 qualifying them as light-weight fill material and the compaction curves are not sensitive to water content. The hydraulic conductivity of RAS:FA varies between 2×10−4 cm/s and 3×10−5 cm/s for FA content varying between 0% and 20% resulting in a largely drainable material. RAS has a friction angle (φ′) of 36° and cohesion (c′) of 24 kPa. Addi...
Use of recycled materials promotes sustainability in geotechnical construction. Compaction characteristics, hydraulic conductivity, shear strength, and compressibility of bottom ash (BA), foundry slag (FS), recycled asphalt pavement (RAP), and recycled asphalt shingles (RAS) that are produced in large quantities were characterized. Results showed that BA, FS, and RAS have lower maximum dry unit weight than compacted sand and the dry unit weights are not sensitive to compaction moisture content. Shear strength of the tested recycled materials are adequate to provide stability for typical highway embankments. The measured hydraulic conductivities provide sufficient drainage capacity for embankment fills. Results of one-dimensional compression tests showed that BA and FS have comparable compressibility to that of compacted sand up to vertical effective stress (σ'v) of 200 kPa after which BA and FS exhibited higher compressibility than sand due to crushing of individual particles. Compressibility of RAS is significantly higher than that of sand, which makes the material unsuitable as embankment fill. RAP consistently has higher compressibility than sand; however, settlement of typical highway embankments constructed with RAP is still below the typical allowable limit. BA, FS, and RAP have appropriate engineering properties for use as structural fill in typical highway embankments. RAS should be mixed with at least 50% of granular additive to reduce compressibility to an acceptable limit. Construction of embankments with RAS mixture or RAP is recommended during warm seasons to induce thermal preloading and reduce compressibility.
1 April 2017 in Journal of Geotechnical and Geoenvironmental Engineering
Recycled asphalt pavement (RAP) can be beneficially used as alternative construction material in geotechnical applications, but characterizing its creep response is important to account for potential viscous effects attributable to the material’s asphalt content. Effects of elevated temperature (35 and 50°C) on creep behavior of compacted RAP specimens were investigated through temperature-controlled triaxial compression tests at sustained deviator stresses. RAP compacted at room temperature (22°C) and subjected to deviator stress at elevated temperature showed creep strain and strain rate that systematically increased with increasing temperature. Time to creep rupture decreased with increasing temperature. Compaction at elevated temperature resulted in denser specimens and reduced creep strain and strain rate. Temperature effects were incorporated into a creep model that may be used to estimate strain rate of RAP at elevated temperatures. Construction of structural fills containing RAP is recomme...
1 February 2018 in Journal of Geotechnical and Geoenvironmental Engineering
Compressibility of five different samples of waste foundry sand (WFS) was evaluated through one-dimensional and triaxial compression tests to assess permanent strains under vertical and deviator stresses present in typical highway embankments. Results show that WFS containing a blend of sand and bentonite had higher compressibility than compacted natural sand. Compressibility of WFS is dependent on stress magnitude, time, and bentonite content. All samples of WFS exhibited one-dimensional secondary compression and deviatoric creep response similar to that of compacted natural soils. Compressibility and potential for creep rupture systematically increased with increasing bentonite content. For samples with relatively high bentonite content (12.8%), the maximum deviator stress to prevent creep rupture was reduced to 65% of the material’s compressive strength. One-dimensional compressibility parameters for compacted WFS were characterized as functions of bentonite content. Models were developed to estimate secondary compression ratio, deviatoric creep strain rates, and time to creep rupture for WFS at different stress levels and bentonite contents.