This paper reports on mechanical design, optimization, and experimental testing of a novel piezo-actuated elliptical vibration-assisted cutting (EVC) system constructed by flexure hinges. The stroke and natural frequency were analyzed based on the theoretical modeling. An enhanced central composite design was chosen as the design of experiments methodology to reduce the modeling error, and a nondominated sorted genetic algorithm-II (NSGA-II) was adopted for structure optimization. The optimized EVC generator was manufactured and experimentally tested to investigate practical properties of the proposed EVC system. It shows that the stroke of input end can reach to 30 μm with a motion resolution of 10 nm, and the first natural frequency can reach to 2600 Hz without considering the manufacturing error. Besides, a relatively small cross-axis coupling ratio (within 0.21%) can be effectively obtained. The developed EVC system is advantageous not only to being equipped with machine tools with various configurations, but also to easily achieving arbitrary vibrations in three-dimensional space through two actuators, which is especially important for the generation of complex structured surfaces. With this paper, it is of great significance to promote industrial application of EVC techniques.

It is known that there are some grinding issues for difficult-to-machine materials, such as adhesion of the grinding wheel, grinding burns, and poor surface quality. In this work, a novel abrasive tool which was based on the principle of liquid body armor was developed with flexible composite to improve the grinding performance. During grinding, particles in the abrasive tool will produce a “hydro-cluster effects” to remove the micro convex of the workpiece surface in a high-shear and low-pressure manner. Rheological measurement of prepared shear thickening fluid (STF) and shear thickening abrasive fluid (STAF) showed that the prepared STF and STAF possessed superior shear thickening properties. In addition, the grinding experiments were carried out to investigate the performance of the novel abrasive tool. Surface roughness of the Inconel718 workpiece decreased from Ra 1.55 μm to Ra 0.38 μm within 90 min. The original pretreatment marks were completely eliminated and the better surface finish was achieved. The surface quality of Inconel718 was greatly improved after grinding. Experimental results verified the effectiveness of the novel high-shear and low-pressure abrasive tool. This work is quite potential to provide an alternative new abrasive tool for the grinding of difficult-to-machine materials in manufacturing industries.

A new piezoelectric tool actuator (PETA) for elliptical vibration turning has been developed based on a hybrid flexure hinge connection. Two double parallel four-bar linkage mechanisms and two right circular flexure hinges were chosen to guide the motion. The two input displacement directional stiffness were modeled according to the principle of virtual work modeling method and the kinematic analysis was conducted theoretically. Finite element analysis was used to carry out static and dynamic analyses. To evaluate the performance of the developed PETA, off-line experimental tests were carried out to investigate the step responses, motion strokes, resolutions, parasitic motions, and natural frequencies of the PETA along the two input directions. The relationship between input displacement and output displacement, as well as the tool tip’s elliptical trajectory in different phase shifts was analyzed. By using the developed PETA mechanism, micro-dimple patterns were generated as the preliminary application to demonstrate the feasibility and efficiency of PETA for elliptical vibration turning.

A novel three-dimensional (3D) elliptical vibration turning device which is on the basis of the leaf-spring-flexure-hinges-based (LSFH-based) double parallel four-bar linkages (DPFLMs) has been proposed. In order to evaluate the performance of the developed 3D elliptical vibration cutting generator (EVCG), the off-line tests were carried out to investigate the stroke, dynamic performance, resolution, tracking accuracy and hysteresis along the three vibration axes. Experimental results indicate that the maximum stroke of three vibration axes can reach up to 26 μm. The working bandwidth can reach up to 1889 Hz. The resolution and hysteresis tests show that the developed 3D EVCG has a good tracking accuracy, relative high resolution and low hysteresis, which is appropriate for micro/nano machining. Kinematical modeling is carried out to investigate the tool vibration trajectory. Experimental results shown that the simulation results agree well with the experimental one, which indicate that the developed 3D EVCG can be used as an option for micro/nano machining.

Based on the clustering effect of shear-thickening fluids (STFs), a high-shear low-pressure flexible grinding wheel has been developed. In order to explore the material removal mechanism, the coupled Eulerian—Lagrangian (CEL) method is adopted to simulate the novel grinding process. The simulation results show that particle clustering effects do occur at the tangential and bottom positions of the micro-convex peak when it instantaneously strikes the workpiece surface. The particle clusters drive the harder abrasive particles to resist the strong interactions of micro-convex peaks. The micro-convex peaks are removed due to the cutting effect of the harder abrasive particles. Compared with traditional grinding, the ratio of tangential force to normal force for the high-shear low-pressure flexible grinding wheel is improved. The various trends in force ratio are consistent with the experimental results, which verifies the effectiveness of high-shear low-pressure grinding.

Titanium alloy is a typical difficult-to-machine material with features of superhigh strength and hardness, and low elastic modulus. It is difficult to guarantee the processing quality and efficiency due to the high cutting force and tool wear in conventional cutting. Elliptical vibration cutting (EVC) as an effective method can improve the machinability of titanium alloys. In this paper, the finite element method (FEM) was adopted to study the cutting force and residual stress of 3D EVC in machining of Ti6Al4V. The Johnson-Cook constitutive model was utilized to illustrate the plastic behavior of Ti6Al4V alloy. The kinematics of the 3D EVC was described, and then the influence of various cutting speeds, vibration amplitudes, vibration frequencies and depths of cut on cutting force and residual stress were carried out and analyzed. The simulation results show that the cutting speed, vibration amplitude a, vibration frequency and depth of cut have larger effect on principal force. In addition, the compressive stress layer can be easily obtained near the machined surface by using 3D EVC, which is helpful to improve the working performance of workpiece.