Bird flight involves complicated wing kinematics, especially during hovering flight. The detailed aerodynamic effects of wings with higher degrees of freedom (DOFs) remain to be further investigated. Therefore, we designed a novel multiarticulate flapping-wing robot with five DOFs on each wing. Using this robot we aimed to investigate the more complicated wing kinematics of birds, which are usually difficult to test and analyze. In this study the robot was programmed to mimic the previously observed hovering motion of passerines, and force measurements and particle image velocimetry experiments. We experimented with two different wing-folding amplitudes: one with a larger folding amplitude, similar to that of real passerines, and one with only half the amplitude. The robot kinematics were verified utilizing direct linear transformation, which confirmed that the wing trajectories had an acceptable correlation with the desired motion. According to the lift force measurements, four phases of the wingbeat cycle were characterized and elaborated through camera images and flow visualization. We found that the reduction in folding amplitude caused a higher negative force during upstrokes and also induced a greater positive force at the initial downstroke through ‘wake capture’. This could increase the vertical oscillation while hovering despite a minor increase in average force production. This phenomenon was not observed during forward flight in previous studies. Our results provide a critical understanding of the effect of wing folding which is required for designing the wing kinematics of future advanced flapping-wing micro aerial vehicles.

This work investigates the effects of body angle and wing deformation on the lift of free-flying butterflies. The flight kinematics were recorded using three high-speed cameras, and particle-image velocimetry (PIV) was used to analyze the transient flow field around the butterfly. Parametric studies via numerical simulations were also conducted to examine the force generation of the wing by fixing different body angles and amplifying the chordwise deformation. The results show that appropriately amplifying chordwise deformation enhances wing performance due to an increase in the strength of the vortex and a more stabilized attached vortex. The wing undergoes a significant chordwise deformation, which can generate a larger lift coefficient than that with a higher body angle, resulting in a 14% increase compared to a lower chordwise deformation and body angle. This effect is due to the leading-edge vortex attached to the curved wing, which alters the force from horizontal to vertical. It, therefore, produces more efficient lift during flight. These findings reveal that the chordwise deformation of the wing and the body angle could increase the lift of the butterfly. This work was inspired by real butterfly flight, and the results could provide valuable knowledge about lift generation for designing microaerial vehicles.

This study investigates the aerodynamic effects of wing membrane elasticity inspired by bats, which exhibit exceptional maneuverability and stability. By mimicking bat wing folding and flapping motions, a 2-DOF flapping mechanism was developed to examine the impact of wing membrane elasticity. Polydimethylsiloxane (PDMS) membranes with tunable elastic properties were fabricated by adjusting the ratio of the curing agent (B agent), with the 1/50 ratio exhibiting the greatest extensibility and the lowest Young’s modulus. Experimental results demonstrate that wing membrane elasticity significantly influences aerodynamic performance. During flapping, increased elasticity led to larger camber changes, enhancing vertical lift through stronger leading-edge vortices, as confirmed by PIV flow field measurements. However, when elasticity became excessively high, as in the 1/50 membrane, the lift benefit diminished, and horizontal force decreased, indicating a trade-off between vertical and horizontal aerodynamic performance. Additionally, the folding mechanism was found to be critical for drag reduction, reducing nearly 50% of negative horizontal forces during flight. By integrating adjustable wing membrane properties and a bioinspired flapping mechanism, this research provides valuable insights into the aerodynamic characteristics of bat flight. These findings not only enhance the understanding of flapping wing aerodynamics but also offer guidance for the design of efficient and agile bioinspired aerial vehicles.

An alula is a small structure of feathers that prevents birds from stalling. In this study, the aerodynamic effect of an alula-like vortex generator (alula-VG) on a revolving wing was investigated using the PIV technique in a water tank. The alula-VG was mounted on a rectangular wing model at two spanwise positions. The wing model with a revolving motion was installed at different angles of attack, which included pre-stall and post-stall conditions. The velocity fields around the wing model with/without an alula-VG were measured and analyzed, including the vorticity contour, the circulation of vortex structures, and the corresponding sectional lift coefficient, which are used to explain the aerodynamic effect induced by an alula-VG. The lift-off and bursting of the leading-edge vortex (LEV) affect the magnitude of the chordwise circulation and the section lift coefficient. The results show that compared to an alula-VG mounted fixed wing model, the flow interactions among the alula-VG induced spanwise flow, the inertial force caused by the revolving motion, and the wing-tip vortex play important roles in the vortex bursting and the resultant aerodynamic performance. The effect of an alula-VG on a revolving wing depends on its spanwise position and the angle of attack of a wing model, which need to be properly matched.