High-chromium cast iron (HCCI) coatings with multicomponent carbides were prepared on low-alloy steel substrates using a laser cladding technique in this work. The microstructure and wear resistance of the coatings were characterized via optical microscopy, scanning electron microscopy, transmission electron microscopy, energy-dispersive spectroscopy, X-ray diffraction and block-on-ring wear testing. Multicomponent carbides (Ti, Nb, Mo, W, V)C with an FCC structure and multicomponent compounds (Nb, Mo, W, V) (B,C) with an FCC structure were found in the microstructures of coatings after multielement doping. In addition, (Cr, Mo, W, V)23C6 compounds could be obtained by heat treatment. These multicomponent compounds were beneficial for obtaining coatings with an excellent hardness (60 HRC) and high wear resistance. This multielement doping method provides an effective modified method for preparing high-wear-resistance laser cladding coatings.
Tungsten doping is critical for the wear resistance and application of High-Chromium Cast Iron (HCCI). A series of investigations of (Fe, Cr, W)7C3 carbides were performed by first principles calculations and experimental analysis. The calculated results showed that with the increase in tungsten content in M7C3, the equilibrium cell volumes and the density gradually increased, and the formation energy of M7C3 carbides gradually decreased. The TEM results showed that the (Fe, Cr, W)7C3 carbides were (Fe3.27Cr2.99W0.74) C3 with a hexagonal structure after adding 2.13 wt % tungsten into laser cladding coatings of High-Chromium Cast Iron with a composition of Fe-26.8 wt % Cr-3.62 wt % C. These results from calculations and in situ nanoindentation show that tungsten doping could improve the ductility and indentation modulus of (Fe, Cr)7C3 carbides, and the composition of (Fe, Cr, W)7C3 was expected to be a high hardness and softness material. The wear test results showed that the wear resistance of tungsten-bearing HCCI was better than ordinary HCCI.
12 July 2018 in IOP Conference Series: Materials Science and Engineering
The chopped roller is the main working part of green fed harvester, of which performance directly affects the cutting effect and power consumption of the machine. A new type hob-type closed chopped roller is designed because of the large cutting resistance of the harvester, and the blade on the roller is arranged in a double row herringbone. It does dynamics analysis for chopped roller and gets three affect parameters, they are cutting speed, sliding cutting angle and grinding blade angle. Under the condition that the blade sharp degree is consistent, take the cutting resistance torque as test aim, the influence of cutting speed, sliding cutting angle and grinding blade angle to cutting resistance torque was studied by using orthogonal test of secondary rotation, the main order of the influence of each factor on the index is cutting speed > grinding blade angle > sliding cutting angle. When the cutting speed is 1200 r/min, sliding cutting angle is 25°, grinding blade angle is 25° which is the best parameter combination for the cutting resistance torque. The experimental results provide data support for further optimization of the chopped roller.
24 May 2017 in DEStech Transactions on Engineering and Technology Research
In the north of China, the road is covered with the solid ice-snow which seriously affects the traffic safety of the city, it is a problem that how to clear the solid ice-snow quickly and efficiently. The concave disc clearing machine and the vertical milling clearing machine have been developed respectively based on the thought of agricultural machinery concave disc and vertical milling principle. The concave disc clearing machine is the clearing plate passively cutting ice-snow, which can complete crushing, cutting, scraping, tilt and push five operations. The vertical milling clearing machine is the cutting knife actively cutting ice-snow with function of milling, crushing, copying, obstacle etc, which has a very strong crushing capacity for ice film like high density ice-snow. The comprehensive clearing snow performance test of the concave disc and vertical milling clearing machine were performed under three kinds of road conditions. The test results show that the concave disc machine and the vertical milling machine have good operation, high working efficiency and the clearing rate are all higher than 90%, parameters setting and all indexes can meet the requirements of snow clearing operations. The concave disc machine is suitable for the plate compacted ice-snow which density is lower than 550 kg/m3 and thickness range from10 mm to 80 mm. The vertical milling machine is suitable for the plate and ice film ice-snow which density range from 300 to 750kg/m3 and thickness is lower than 50mm, especially suitable for ice film freezing ice -snow, which density is higher than 550kg/m3.