Spatter is an inherent, unpreventable, and undesired phenomenon in laser powder bed fusion (L-PBF) additive manufacturing. Spatter behavior has an intrinsic correlation with the forming quality in L-PBF because it leads to metallurgical defects and the degradation of mechanical properties. This impact becomes more severe in the fabrication of large-sized parts during the multi-laser L-PBF process. Therefore, investigations of spatter generation and countermeasures have become more urgent. Although much research has provided insights into the melt pool, microstructure, and mechanical property, reviews of spatter in L-PBF are still limited. This work reviews the literature on the in situ detection, generation, effects, and countermeasures of spatter in L-PBF. It is expected to pave the way towards a novel generation of highly efficient and intelligent L-PBF systems.

Ag and Cu have different advantages and are widely used in key fields due to their typical highly electrical and thermal conductive (HETC) properties. Laser powder bed fusion (LPBF), an innovative technology for manufacturing metallic multi-material components with high accuracy, has expanded the application of Ag–Cu in emerging high-tech fields. In this study, the multi-material sandwich structures of Ag7.5Cu/Cu10Sn/Ag7.5Cu were printed using LPBF, and the formation mechanism, interface characteristics, and molten pool behavior of the Ag7.5Cu/Cu10Sn (A/C) and Cu10Sn/Ag7.5Cu (C/A) interfaces were studied to reveal the influence of different building strategies. At the A/C interface, pre-printed Ag7.5Cu promoted Marangoni turbulence at a relatively low energy density (E_A/C = 125 J/mm³). Due to the recoil pressure, the molten pool at the A/C interface transformed from a stable keyhole mode to an unstable keyhole mode. These phenomena promoted the extensive migration of elements, forming a wider diffusion zone and reduced thermal cracking. At the C/A interface, the molten pool was rationed from the conduction mode with more pores to the transition mode with fewer defects due to the high energy density (E_C/A = 187.5 J/mm³). This work offers a theoretical reference for the fabrication of HETC multi-material structures via LPBF under similar conditions.

The plasma rotating electrode process (PREP) is an ideal method for the preparation of metal powders such as nickel-based, titanium-based, and iron-based alloys due to its low material loss and good degree of sphericity. However, the preparation of silver alloy powder by PREP remains challenging. The low hardness of the mould casting silver alloy leads to the bending of the electrode rod when subjected to high-speed rotation during PREP. The mould casting silver electrode rod can only be used in low-speed rotation, which has a negative effect on particle refinement. This study employed continuous casting (CC) to improve the surface hardness of S800 Ag (30.30% higher than mould casting), which enables a high rotation speed of up to 37,000 revolutions per minute, and silver alloy powder with an average sphericity of 0.98 (5.56% higher than gas atomisation) and a sphericity ratio of 97.67% (36.28% higher than gas atomisation) has been successfully prepared. The dense S800 Ag was successfully fabricated by laser powder bed fusion (LPBF), which proved the feasibility of preparing high-quality powder by the “CC + PREP” method. The samples fabricated by LPBF have a Vickers hardness of up to 271.20 HV (3.66 times that of mould casting), leading to a notable enhancement in the strength of S800 Ag. In comparison to GA, the S800 Ag powder prepared by “CC + PREP” exhibits greater sphericity, a higher sphericity ratio and less satellite powder, which lays the foundation for dense LPBF S800 Ag fabrication.

Direct ink writing of multiple mineral materials (M ³ ) coupled with simulation analysis is an optimization solution in accordance with low-carbon and sustainable manufacturing. It improves the ability to imitate natural biological iterative optimization, and accurately obtained data for geological model tests to effectively help prevent natural disasters. This article investigates the effects of equivalent materials on the direct ink writing and permeability behaviors through geological simulation models. The mineral compositions provide adjustable cohesion and compression coefficient properties and considerably improve the stability and dispersion of slurry by adjusting parameters such as the viscosity, filling ratio, and deposition height. The upper limit of the permeability depends on the designed macropores and the printing accuracy because macro features provide pathways for rapid water infiltration into the printed specimen. This research establishes guidelines for the fabrication of components with tailored and designed-pore-dependent permeability properties that are primarily for slope geotechnical engineering applications.