Qiang Chen

Dr. Qiang Chen


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 December 2017 in IEEE Access
Verified
Journal Article
Open access
QCQiang Chen
Qiang Chen
YTYing Tan
Ying Tan
JLJie Li
Jie Li
IMIven Mareels
Iven Mareels
A decentralized proportional-integral-differential (PID) control structure has been always the first option for magnetic levitation systems due to its model-free nature as well as the simplicity. It is very challenging to tune PID parameters for each suspension point to ensure that the closed-loop system is less sensitive to uncertainties/disturbances. Even though, by a large number of experiments, a reasonably good PID control parameter set can be obtained to levitate a single suspension point for a given set point, these parameters are very sensitive when the set point changes or the decentralized PID controller is applied to the half bogie where coupling exists, strong oscillations will be observed and retuning of parameters is needed. This paper utilizes the extremum seeking (ES) method to tune PID parameters on-line to improve the steady-state performance of the system with few oscillations. A “sampled-data”structure is used to obtain a moving window approximation of the steady-state behavior, leading to a discrete-time ES tuning for the decentralized PID parameters. By using projection method, the tuning parameters are constrained in a compact set, in which the stability can be guaranteed and the optimal performance can be achieved. Experiments have shown the effectiveness of the proposed method.

23 August 2023 in IEEE Transactions on Intelligent Vehicles
Verified
Journal Article
Closed access
YTYiqiu Tan
Yiqiu Tan
DZDanfeng Zhou
Danfeng Zhou
JLJie Li
Jie Li
QCQiang Chen
Qiang Chen
ZJZhen Jia
Zhen Jia
MLMingxin Liu
Mingxin Liu
Due to the advantages of no active control, self-stability, large clearance, and small self-weight, the electrodynamic suspension system has a wide range of applications in high-speed fields such as ultra-high speed maglev transportation, electromagnetic ejection and rocket propulsion. Based on dynamic circuit theory, Neumann equation, and virtual displacement method, the electromagnetic force calculation model of the null-flux coil superconducting electrodynamic suspension system is obtained, and a dynamic window algorithm is designed to accelerate the electromagnetic force calculation speed. Co-simulation platform is built to overcome the difficulty in dynamic solution of the vehicle. The results of the co-simulation reflect the motion status of the vehicle under different working conditions, revealing the potential dynamic problems of the superconducting electrodynamic suspension system.

4 September 2019 in Symmetry
Verified
Journal Article
Open access
PDF file
ZGZhaoyu Guo
Zhaoyu Guo
DZDanfeng Zhou
Danfeng Zhou
QCQiang Chen
Qiang Chen
PYPeichang Yu
Peichang Yu
JLJie Li
Jie Li
The research of ground high speed systems has been popular, especially after the announcement of Hyperloop concept, and the analysis of the suspension structure is critical for the design of the system. This paper focuses on the design and analysis of a plate type electrodynamic suspension (EDS) structure for the ground high speed system. The working principle of proposed whole system with functions of levitation, guidance and propulsion is presented, and the researched EDS structure is composed of permanent magnets (or superconducting magnets) and non-ferromagnetic conductive plates. Levitation and guidance are achieved by forces generated through the motion of the magnets along the plates. The plate type EDS structure is analyzed by three-dimensional (3D) finite element method (FEM) in ANSYS Maxwell. Structure parameters that affect the EDS performances are investigated, which include dimensions of magnets and plates, plate material, the relative position between magnets and plates, and arrangement of magnets. The properties of forces are discussed, especially for the levitation force, and the levitation working point is decided based on the analysis. Levitation-drag ratio of the plate type structure is investigated, and it improves with the increasing of vehicle velocity. The analysis results indicate that the plate type EDS structure is feasible for applications in ground high speed systems. The following study will focus on the dynamic research of the EDS system.

1 August 2018 in IEEE Access
Verified
Journal Article
Open access
QCQiang Chen
Qiang Chen
YTYing Tan
Ying Tan
JLJie Li
Jie Li
DODenny Oetomo
Denny Oetomo
IMIven Mareels
Iven Mareels
This paper presents a half bogie model of magnetic levitation systems, which can capture the mechanical coupling between two suspension points. Based on the half bogie model, a model-guided state feedback controller is designed to stabilize the nominal model. A new extended state observer using measured data is proposed to estimate the unknown system state as well as the modeling uncertainties, disturbances, and coupling. This leads to an active disturbance rejection controller that can cancel the effect of unknown disturbances. By incorporating model-guided state feedback controller and the data-driven active disturbance rejection controller with an appropriate tuning of parameters, the closed loop system can track the desired gap up to any given accuracy. Simulation and experimental results demonstrate the effectiveness of the proposed method.

31 July 2024 in IEEE Transactions on Intelligent Transportation Systems
Verified
Journal Article
Closed access
YTYiqiu Tan
Yiqiu Tan
DZDanfeng Zhou
Danfeng Zhou
MQMinghe Qu
Minghe Qu
JLJie Li
Jie Li
QCQiang Chen
Qiang Chen
MLMingxin Liu
Mingxin Liu
The superconducting electrodynamic suspension system has many advantages such as no active control, large clearance, and small weight, but its insufficient vertical damping is a problem that needs to be solved. A novel design of the active damping system is proposed, so the vertical damping force can be generated by the interaction between the energized traction coils and the active damping coils. By decomposing the superconducting electrodynamic suspension system into suspension system, traction system, and active damping system, and establishing mathematical models for electromagnetic force calculation in each subsystem, the working mechanisms of each subsystem are well analyzed. Furthermore, based on genetic algorithm, the size and installation position of the active damping coils are optimized, and the optimization result is consistent with the theoretical analysis of the active damping system. A co-simulation platform including electromagnetic force calculation and vehicle dynamics is built, and the co-simulation analysis verified that the proposed active damping system has good suppression effect on vertical and pitch angular motion of the vehicle.

7 February 2020 in IEEE Access
Verified
Journal Article
Open access
YLYajian Li
Yajian Li
DZDanfeng Zhou
Danfeng Zhou
PCPeng Cui
Peng Cui
PYPeichang Yu
Peichang Yu
QCQiang Chen
Qiang Chen
JLJie Li
Jie Li
The controlled air gap of the electromagnetic levitation system of maglev train is generally 8-10mm, which makes the vehicle/guideway coupling problem prominent. In practice, it is found that the stability of the magnetic levitation system is affected by guideway irregularities, and the levitation gaps show different dynamic characteristics, which is closely related to the sensor positions. The purpose of optimization of the dynamic performance of the electromagnetic levitation system is to reduce the dynamic deviation amplitude of the levitation gaps. Firstly, a linear model of the module levitation system with guideway is proposed. On this basis, the discrete frequency excitation method is used to obtain the dynamic amplitude response of the levitation gaps at different guideway wavelengths and vehicle speeds. Then, an optimization framework based on sensor positions is proposed. Based on this framework, the optimal sensor position at different speeds is obtained. The simulation results show that the optimal scheme can effectively reduce the deviation amplitude and the difference between the two levitation gaps, thus improving the dynamic performances of the electromagnetic levitation system.