We experimentally studied the inscription of fiber Bragg gratings by using femtosecond (fs) laser point-by-point (PbP) technology. The effects of the focusing geometry, grating order, laser energy and grating length on the spectral characteristics of the PbP FBG were investigated. After optimizing these parameters, a high-quality first-order PbP FBG with a reflectivity > 99.9% (i.e., Bragg resonance attenuation of 37.7 dB) and insertion loss (IL) of 0.03 dB was successfully created. Moreover, taking advantage of the excellent flexibility of the fs laser PbP technology, high-quality FBGs with various Bragg wavelengths ranging from 856 to 1902.6 nm were inscribed. Furthermore, wavelength-division-multiplexed (WDM) FBG arrays consisting of 10 FBGs were rapidly constructed. Additionally, a Fabry-Perot cavity was realized by using two high-quality FBGs, and its birefringence could be reduced from 3.04 × 10−5 to 1.77 × 10−6 by using a slit beam shaping-assisted femtosecond laser PbP technology. Therefore, such high-quality FBGs are promising to improve the performance of optical fiber sensors, lasers and communication devices.
Single-frequency distributed Bragg reflector fiber lasers (DBR FLs) are attractive as sensing elements for detecting weak vibration or acoustic signals in extreme environments. However, conventional UV-written DBR FLs operate with two orthogonal polarization modes and can hardly operate in high-temperature environments. Herein, we propose the fabrication of polarization-controllable DBR FLs by using a slit beam shaping femtosecond (fs) laser point-by-point technology. High-quality fiber Bragg grating Fabry-Perot (FBG-FP) cavities with insertion loss as low as 0.2 dB are directly inscribed in Er-doped fibers to create DBR FLs. Both single-polarization and dual-polarization DBR FLs are created by changing the fs laser-induced birefringence using a mechanical slit. In addition, a DBR FL array consisting of eight DBR FLs is also successfully created. Experimental results show that the fabricated DBR FL can withstand a high temperature up to 800 °C and the laser linewidth increases from 1.55 kHz to 10.8 kHz as temperature raising from 25 °C to 800 °C. Furthermore, high-temperature vibration sensing at 800 °C is realized by using a single-polarization DBR FL, achieving an acceleration sensitivity of 0.319 rad/(m/s 2 ). Moreover, a dual-polarization DBR FL is served as an ultrasonic sensor, realizing the ultrasonic non-destructive evaluation (NDE) in a 7075-aluminum plate.
We propose and demonstrate a novel high-temperature-resistant vector accelerometer, consisting of a ring cavity laser and sensing probe (i.e., fiber Bragg gratings (FBGs)) inscribed in a seven-core fiber (SCF) by using the femtosecond laser direct writing technique. A ring cavity laser serves as a light source. Three FBGs in the outer cores of SCF, which are not aligned in a straight line, are employed to test the vibration. These three FBGs have 120° angular separation in the SCF, and hence, vibration orientation and acceleration can be measured simultaneously. Moreover, the FBG in the central core was used as a reflector in the ring cavity laser, benefiting to resist external interference factors, such as temperature and strain fluctuation. Such a proposed accelerometer exhibits a working frequency bandwidth ranging from 4 to 68 Hz, a maximum sensitivity of 54.2 mV/g, and the best azimuthal angle accuracy of 0.21° over a range of 0–360°. Furthermore, we investigated the effect of strain and temperature on the performance of this sensor. The signal-to-noise ratio (SNR) only exhibits a fluctuation of ~1 dB in the range (0, 2289 με) and (50 °C, 1050 °C). Hence, such a vector accelerometer can operate in harsh environments, such as in aerospace and a nuclear reactor.