Aiping Tang

Aiping Tang


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 October 2022 in Geotechnics
Verified
Journal Article
Open access
PDF file
HQHaigang Qu
Haigang Qu
DMDianrui Mu
Dianrui Mu
ZRZhenlu Ren
Zhenlu Ren
ZHZiyuan Huang
Ziyuan Huang
YHYang Huang
Yang Huang
ATAiping Tang
Aiping Tang
The construction of high-speed railways in cold regions needs to consider the effects of freeze–thaw cycles (FTHs) on the long-term deformation of subgrades. However, at present, research on the creep characteristics of frozen–thawed rocks and soils is not extensive. In the limited studies on frozen–thawed soil creep properties, current research focuses more on high stress–strain–time responses, but for the subgrades, the inner stress is usually low. This paper presents the results of triaxial compression creep tests on remolded, frozen–thawed silty clay sampled in the Yichun-Tieli area and describes its stress–strain–time relationship in an arctan function-based mathematical model. Each creep test condition is studied using three specimens. Frozen–thawed silty clay exhibits attenuation creep under low-level stress. In general, from 4 FTHs to 11 FTHs, the mean elasticity modulus decreases first, and then, increases. The exerted stress is higher than the yield stress; the more FTHs the specimens experience, the more time they need to be deformed stably under the same axial deviatoric stress (ADS). Under the same mean ADS, the mean stable strain of 7 FTHs exceeds the other two FTH conditions and, in general, the mean stable strain of 4 FTHs exceeds 11 FTHs. By dissecting the phenomena, it can be concluded that with FTHs increasing, moisture and voids reconstitute in the process; the elastic strain accounts for most of the total strain and significantly decides the extent of creep deformation; the arctan function-based model is basically able to describe, but not perfectly predict, the stress–strain–time relationship of frozen–thawed silty clay.

30 September 2022 in Geotechnics
Verified
Journal Article
Open access
PDF file
HQHaigang Qu
Haigang Qu
DMDianrui Mu
Dianrui Mu
ZNZhong Nie
Zhong Nie
ATAiping Tang
Aiping Tang
Numerous researchers of soil creep behavior adopt stepwise loading (SL) rather than respective loading (RL) to perform the triaxial creep tests. However, a complete continuous strain–time curve of SL needs to be converted into assumed curve clusters supposing obtained under RL before the deformation data are used to develop creep constitutive models. Classical methods realize the conversion mainly by focusing on the creep deformation parts and classifying them into linear and nonlinear compositions. Mostly, the linear parts are simply superposed while the nonlinear parts are complex to consider and so are neglected. Moreover, classical methods are not sufficiently valid to eliminate the stress history effect on the conversion. Here, a new method is proposed to achieve the conversion without neglecting the stress history effect. The method rebuilds the triaxial creep test mathematically and physically, adhering to the revising of energy. The method treats the tested deformation in its entirety, instead of distinguishing it into elastic, visco-elastic, plastic and creep (linear and nonlinear) deformation to convert respectively. The comparison among actual measured SL and RL strain–time curves and the curves converted by the new method proves the stress history effect should not be neglected. The higher the vertical load level, the larger the discrepancy between the RL and SL strain–time curve, and the disparity becomes larger with time. The new method highlights the necessity of considering the stress history effect in analysis and design for higher accuracy. The comparisons illustrate the conversion method at least produces more satisfactory results for clayey soil. Primarily examined, at the later stages of loading, the disparity in strain between the converted RL and measured RL decreases by 52.5%~53.5% compared with strain between the measured SL and measured RL.