Mohamed NASSER

Dr. Mohamed NASSER


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Closed access
PDF file
BMBen REZG Mehrez
Ben REZG Mehrez
MNMohamed NASSER
Mohamed NASSER
RORomdhane Othmani
Romdhane Othmani
Alex MontagneAlex Montagne
Alex Montagne

25 November 2024 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
MNMohamed NASSER
Mohamed NASSER
BMBen REZG Mehrez
Ben REZG Mehrez
Mamoun FellahMamoun Fellah
Mamoun Fellah
Alex MontagneAlex Montagne
Alex Montagne

1 November 2021 in Materials Research Express
Verified
Journal Article
Open access
PDF file
MNMohamed NASSER
Mohamed NASSER
SASlimen Attyaoui
Slimen Attyaoui
BTBrahim Tlili
Brahim Tlili
AMAlex Montagne
Alex Montagne
JBJalel Briki
Jalel Briki
AIAlain Iost
Alain Iost
Nanoindentation is a technique commonly used to measure the mechanical properties of thin films even at depths less than 1 μm. In fact, the characterization is based on the study of the load/displacement curves resulting from the nanoindentation test. We aim to use the backtracking search optimization algorithm (BSA) to improve the extraction of P(h) curves performed by nanoindentation on galvannealed Fe-Zn coating in terms of precision and dispersion. Indeed, the originality of this study is not limited only to the P(h) curve extraction methods, but also to its application in modeling the reverse approach for the case of Fe-Zn coating deposited on a Dual-Phase DP600 steel substrate. Indeed, the BSA approach showed more precision (with respect to the determined mean value) and less dispersion (magnitude of error around the identified mean value) compared to the Least-squares approach. The average error with the BSA and LS methods is respectively 0.89% and 3.16% for the yield stress σ Y and 3.17% and 7.93% for the strain hardening exponent (n). This reduced the error variability in the prediction of the constitutive law to 72% and 60% for ( σ Y ) and n, respectively. Thus, we solved the problems of accessibility, uniqueness of the solution, precision (+10%) and dispersion (−85%) of the required prediction models for the Fe-Zn coating behavior.

16 July 2025 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
BBBoujemaa Hadj Brahim
Boujemaa Hadj Brahim
MNMohamed NASSER
Mohamed NASSER
SASlimen Attyaoui
Slimen Attyaoui
LDLotfi Dahmani
Lotfi Dahmani

29 August 2024 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
BBBoujemaa Hadj Brahim
Boujemaa Hadj Brahim
LDLotfi Dahmani
Lotfi Dahmani
MNMohamed NASSER
Mohamed NASSER
SASlimen Attyaoui
Slimen Attyaoui
AVAleksandr Vorobev
Aleksandr Vorobev

10 July 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
BTB. Tlili
B. Tlili
MNMohamed NASSER
Mohamed NASSER
HGHichem Guizeni
Hichem Guizeni
Alex MontagneAlex Montagne
Alex Montagne
The development and qualification of CrAlN coatings deposited by DC magnetron sputtering offer new industrial solutions to increase the lifecycle of material forming tools (machining and shaping). This study focuses on the selection and optimization of deposition modes for CrAlN layers to be deposited on a 90CrMoV8 tool steel substrate. The adopted methodology aims to optimize the deposition conditions to meet the customer's requirement of a CrAlN coating thickness of approximately 2-3 µm for use in a hot forming process. Different polarizations using two Al and Cr targets, with both stationary and rotating substrate modes during deposition, were tested and evaluated. Characterizations of the CrAlN coating layers (microhardness, residual stress, structures) and performance in service (wear, friction, adhesion, corrosion) were chosen as selection criteria for a particular coating mode. The aluminum content plays a crucial role in the tribological and mechanical behavior of CrAlN layers. Corrosion resistance is more sensitive to the aluminum content for the stationary deposition mode. As a result, the rotating mode provides higher adhesion (+100%) and less wear (-60%) compared to the stationary mode. Therefore, depending on the likely performance in service, either a stationary or rotating mode could be applied for coating the functional surfaces of hot forming tools.