It is well established that hydrogen has become one of the most promising fuels for achieving zero-carbon emissions. However, hydrogen combustion still faces many challenges, particularly the flashback issue and high NOx emissions, which necessitate the exploration of hydrogen combustion technologies and pollution control measures. This paper proposes a micromix diffusion combustion scheme with a disturbance vortex generator (DVG). The flow characteristics of the micromix element were analyzed, including the velocity distribution, penetration depth, jet vortex length, and vortex structure. It was found that DVG would create an air streamwise vortex within the main airflow, thus accelerating the axial velocity decay and facilitating the penetration of hydrogen. The hydrogen jet vortex rolls up the mainstream air, forming a coupled vortex system, which further enhances mixing. Sensitivity analysis was carried out to study the influences of the key parameters of the micromix element. The hydrogen injection hole diameter and the DVG height were found to be the most influential factors. The interactions between vortex, flame, and NOx were investigated to obtain the mechanism of NOx formation. By conducting a comparative analysis of the effects of the hydrogen orifice diameter and the vortex generator height, it has been observed that augmenting the length of the jet vortex can significantly promote the mixing of hydrogen with the mainstream air, playing an essential role in reducing emissions. This study establishes a solid foundation for future research endeavors in the development of micromix diffusion combustors.
4 October 2021 in International Journal of Aerospace Engineering
The increasing demand for power, fuel efficiency, and safety of aeroengines has called for weight reduction and structural integrity examination of the critical components. This paper is aimed at performing a systematic investigation on the design of a high-speed Ti2AlNb blisk, including disc geometry optimization and burst speed prediction. Incorporating the design of the experimental approach and the commercial software has guaranteed that the optimization could be accomplished. Six key parameters were defined as variables with regard to the geometric dimensions whereas the safety factors were set as constraints to make the disc feasible. Sensitivity analysis has been conducted to study the effects of the variables on the safety factors and disc weight. Bore width, web width, and bore angle are identified to be the dominant factors regarding optimization. Results reveal that the bore width and web width are positively related to the safety factors at the cost of increasing the disc weight. On the contrary, the effects of the bore angle show the opposite trend. Finally, the achieved minimum disc weight is 15.2 kg with all the safety factors meeting the requirements. Upon completing the disc shape optimization, the burst speed was estimated using three elaborated methods. The comparisons between the numerical results and the experimental results indicate that the mean stress method is accurate when the correction coefficient is chosen properly. The local stress and strain method and the global plastic instability method also offer a precise prediction on the burst speed with errors of less than 5%. It could also be concluded that the predicted web failure in the radial direction of the disc is in good agreement with the experimental results.
20 May 2022 in Journal of Engineering for Gas Turbines and Power
This paper aims to develop a robust design process by approaching the performance boundaries and evaluating the operability of the pursued geared turbofan (GTF) engine with low specific thrust for entry-into-service (EIS) 2025. A two-spool direct-drive turbofan (DDTF) engine of EIS 2000 was improved according to aircraft specifications and technology boundaries in 2025. A series of optimized engines with consecutive fan diameters were established to seek the ideal engine by balancing specific fuel consumption (SFC), weight, and mission fuel burn. The fan diameter was proved to be a decisive factor for lowering SFC and energy usage. The cycle design optimization process achieved a thermal efficiency of approximately 52%, and a propulsive efficiency of 79.5%, which is 8.19% increase in propulsive efficiency by enlarging fan diameter from 1.6 m to 1.9 m. Meanwhile, the 1.9 m-fan diameter engine achieved a reduction in SFC and fuel burn of 7.47% and 6.58%, respectively, which offers an overall reduction of 30.82% in block fuel burnt and CO2 emission compared to the DDTF engine. A feasibility check verified the viability of the designed optimum engine in terms of fan tip speed, stage loading, and AN2. Dynamic simulation offered a deep understanding of transient behavior and fundamental mechanism of the GTF engine. An important aspect of this paper is the use of advanced ceramic matrix composite (CMC) materials, which led to an improvement of 4.92% in block fuel burn and 2.93% in engine weight.
19 January 2023 in International Journal of Aerospace Engineering
This paper performs a comprehensive investigation on the high cycle fatigue (HCF) life prediction of turbine blade with film cooling holes. The modified theory of critical distance (MTCD) method is proposed to estimate the fatigue life of the specimen considering the notch sensitivity coefficient and multiaxial stress effect. Then, two types of specimens were designed with regard to the single-hole and multihole conditions. Afterwards, the dangerous path and fatigue life of the two specimens were achieved implementing the MTCD method. Then, the experiments and failure analysis were carried out. The results show that the stress concentration and multiaxial stress resulting from the film cooling holes are the primary reasons that the cracks originated. Meanwhile, the dangerous path of the single-hole specimen is quite different from the multihole specimen due to the interhole interference. Finally, most of the calculated fatigue life is within the twice error band of the tested life.
This paper aims to develop an advanced three-shaft turbofan engine with ultrahigh bypass ratio (BPR) for entry-into-service (EIS)2050. The boundary approaching method is utilized to obtain the optimal engine for a series of engines with different fan diameters. Furthermore, the flight mission analysis was carried out to fully consider the engine performance and weight penalty. The optimum engine employs a 3.26 m fan diameter with ultrahigh BPR reaching 21.39. The corresponding specific fuel consumption (SFC) is 11.42 (g/s)/kN, which is 3.88% lower than the 2.95 m fan diameter engine. However, the weight penalty has offset part of the benefits, and the block fuel reduction is 2.5%. Sensitivity analysis results reveal that the low-pressure turbine (LPT) efficiency plays a dominant role in engine performance. Afterwards, the effects of variable geometry are investigated including the blow-off valve (BOV), variable inlet guide vane (VIGV), and bypass variable area nozzle (VAN). Results show that combining the three measures would boost engine performance and save fuel. The designed schedule for the combination of VIGV, BOV, and VAN has generated a reduction in block fuel, NOx, CO2, and H2O reaching 3.36%, 5.55%, 2.47%, and 2.53%, respectively.