Powder-blown laser additive manufacturing adds flexibility, in terms of locally varying powder materials, to the ability of building components with complex geometry. Although the process is promising, porosity is common in a built component, hence decreasing fatigue life and mechanical strength. The understanding of the physical phenomena during the interaction of a laser beam and powder-blown deposition is limited and requires in-situ monitoring to capture the influences of process parameters on powder flow, absorptivity of laser energy into the substrate, melt pool dynamics and porosity formation. This study introduces a piezo-driven powder deposition system that allows for imaging of individual powder particles that flow into a scanning melt pool. Here, in-situ high-speed X-ray imaging of the powder-blown additive manufacturing process of Ti-6Al-4V powder particles is the first of its kind and reveals how laser-matter interaction influences powder flow and porosity formation.
With the increasing requirements for the surface quality of the workpiece, many kinds of hybrid manufacturing have developed recently. Ultrasonic vibration-assisted laser polishing (UVLP) is a new hybrid manufacturing method. Different from the traditional method of applying ultrasonic vibration on the workpiece, this paper applies ultrasonic vibration on the lens. Besides, the thermal mechanisms of the 304 stainless steel polished by traditional laser polishing (TLP) and UVLP were analyzed to reveal the influence of ultrasonic vibration on the polishing effect. The ultrasonic vibration lens transforms the laser polishing into an intermittent polishing process, which affects the laser energy density and the quality of the polished surface. This research was focused on the experimental analysis of the surface morphology and surface roughness of the 304 stainless steel that was processed by UVLP, and compared with TLP. And the effects of laser power, scanning speed, focus offset, and amplitude on the quality of the polished surface were obtained. The preferred process parameters of UVLP 304 stainless steel were obtained by the range analysis and variance analysis of the orthogonal experiment. Experimental results have shown that UVLP can reduce the surface roughness of 304 stainless steel from 2.777 μm to 0.512 μm at most. Thermal mechanism analysis results were verified by experimental results. Choosing appropriate processing parameters can effectively improve the quality of the polished surface, making the processing effect of UVLP significantly better than TLP.
A femtosecond laser could realize a high transition rate of the phase change material (PCM), and the properties of the amorphous and the crystalline Ge2Sb2Te5 (GST) induced by a femtosecond laser were studied, which was one of the candidates among the PCMs. However, the characteristics of the intermediate phase states in reversible phase transitions were also important and helpful to explore the mechanisms of the phase transitions. In this paper, the ultrafast dynamics of amorphous, crystalline face-centered-cubic (FCC), and hexagonal-close-packed (HCP) states were investigated using a femtosecond laser pulse excitation through a reflective-type pump–probe technique, obtained by annealing at certain temperatures, and verified using X-ray diffraction (XRD) and the Raman spectrum. It was found that as the annealing temperature increased, the electron of the GST films could be excited more easily, while the ablation threshold decreased. Due to annealing, the structure of bonding was changed for different phase states, which resulted in the decrease in the band gap of the films. In addition, it was hard for the intermediate state films to transit to the amorphous structure state via the femtosecond laser, and the crystallization would be enhanced, while the crystalline HCP structures of GST could be directly and easily changed to the amorphous state by a pulse, which resulted from the non-thermal phase change caused by the excited electron.
1 March 2020 in Journal of Materials Processing Technology
Element-doped phase change material (PCM) could improve the performances, e.g., better thermal stability, higher electrical resistance, and faster crystallization speed; thus, the influence of the doping element needs to be further investigated. In this paper, a femtosecond laser, which could realize the ultrafast phase transition rate of PCM between amorphization and crystallization, was used to explore the properties of nitrogen-doped Ge2Sb2Te5 (GST), and a bond effect was proposed. The pure GST and different nitrogen contents of doped GST films were investigated by femtosecond laser pulse excitation through a pump–probe shadowgraph imaging technique. The results showed that the element-doped films could change photon absorption because of the increase in free carriers. This caused the faster rate of reflectivity to change in the irradiated area by the laser beam as the more nitrogen doped. When the nitrogen content increased, the crystallization evolution became harder because it enhanced the bond effect, which suppressed crystalline grain growth and improved the thermal stability. Based on the analysis in the paper, the desired performances of PCMs, e.g., ultrafast dynamics, crystallization evolution, and thermal stability, could be controlled according to the demands by modifying the bond effect.