Hao Li

Dr. Hao Li

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 July 2020 in IEEE Transactions on Intelligent Transportation Systems
Verified
Journal Article
Closed access
XFXinyuan Fan
Xinyuan Fan
WZWeige Zhang
Weige Zhang
ZWZhanguo Wang
Zhanguo Wang
FAFulai An
Fulai An
HLHao Li
Hao Li
JJJiang Jiuchun
Jiang Jiuchun
With the development of battery technology, large-scale battery applications are increasing. In order to obtain a higher current and voltage level and improve the overall energy efficiency, batteries are connected in series and parallel. Bulk model is the most used model to simulate battery packs, and the simulation results of single cell are enlarged several times to represent a battery pack. But bulk model ignores inconsistency between the batteries, and when the current magnification is large, such as in the extreme fast charge scenario, this neglect cannot reflect the current distribution inside the battery pack. Our paper proposes a simplify algorithm based on equivalent circuit model, which applied for non-uniform series and parallel-connected batteries. This simplification can greatly improve simulation speed while maintaining accuracy under the consideration of inconsistency. More importantly, this algorithm applies to any complex circuit, regardless of how many series-parallel structure layers. With the proposed algorithm, Monte Carlo simulations were evaluated to obtain the influence of battery series and parallel number and normal distribution parameters on current distribution. Simulation results show that an increase in the number of series will reduce the inconsistency of the current distribution, and an increase in the number of parallel and an increase in the relative standard deviation of the normal distribution of the battery parameters will increase the inconsistency of the current distribution.

17 November 2020 in IEEE Transactions on Intelligent Transportation Systems
Verified
Journal Article
Closed access
HLHao Li
Hao Li
JJJiang Jiuchun
Jiang Jiuchun
WZWeige Zhang
Weige Zhang
LZLinjing Zhang
Linjing Zhang
YYYing Yang
Ying Yang
XFXinyuan Fan
Xinyuan Fan
With the development of extreme fast charging technology, charging stations need to use energy storage stations to reduce the rising peak to average power ratio (PAPR). Lithium-ion capacitor (LIC) is a chemical power source that uses both Faraday process and non-Faraday process to store energy. Because of its attractive performance in terms of rate characteristics and chemical stability, it is suitable for some energy storage stations that consider both power density and energy density. It is important to describe the current-voltage characteristics of LIC to predict the charge and discharge efficiency in the early design of energy storage power stations. During the test, however, a full discharge or charge results in a high temperature rise, and the electrical model parameters near a specific temperature point cannot be accurately obtained. The short current pulses cannot stabilize the polarization. In this paper, a high-accuracy parameters identification method based on an improved Butler-Volmer-Equation-Based electrical model is used to summarize the phenomena caused by the rate of change of high-energy LIC. The accuracy of the method is tested under the dynamic stress condition test. The maximum voltage error is less than 2%. Energy efficiency calculation based on the used model is simulated by the design condition from the energy storage station of the Haizhu line in Guangzhou. The maximum error is less than 0.2%.

13 September 2022 in World Electric Vehicle Journal
Verified
Journal Article
Open access
PDF file
ACAnci Chen
Anci Chen
WZWeige Zhang
Weige Zhang
BSBingxiang Sun
Bingxiang Sun
HLHao Li
Hao Li
XFXinyuan Fan
Xinyuan Fan
The resistance of the internal short-circuit (ISC) has a potential evolution trend accompanied by an increasing safety risk. Thus, an accurate online resistance estimation for the ISC is crucial for evaluating its safety risk and taking staged handling measures. Since the ISC battery mainly presents abnormal stage of charge (SOC) depletion behaviors, the SOC estimation processes based on state observers and battery models will act an important basis of the ISC resistance estimation problem. However, as it will be exhibited in this paper, when directly using the measured voltage of the ISC battery as the output variable of the state observer, the battery model error will limit the SOC estimation accuracy and further lead to very inaccurate or even divergent ISC resistance estimation results for large-format batteries, which present quite slight SOC depletion behaviors at the ISC state. To this end, this paper proposes a novel SOC and ISC resistance co-estimation method which combines a reconstruction method of the model-predicted voltage of the ISC battery. Experimental validations are carried out with a 37 Ah battery, results show that the proposed method which uses the reconstructed model-predicted voltage (RMPV) as the output variable of the state observer only present maximum estimation errors of 39.96 Ω and 2.00 Ω for the ISC resistances of 100 Ω and 10 Ω, respectively.

29 November 2024 in Batteries
Verified
Journal Article
Open access
PDF file
HLHao Li
Hao Li
JCJianan Chen
Jianan Chen
YMYingtao Ma
Yingtao Ma
WLWeizhi Liu
Weizhi Liu
LTLei Tang
Lei Tang
BLBing Liu
Bing Liu
High-frequency ripple current excitation reduces the lithium precipitation risk of batteries during self-heating at low temperatures. To study the heat generation behavior of batteries under high-frequency ripple current excitation, this paper establishes a thermal model of LIBs, and different types of LIBs with low-temperature self-heating schemes are studied based on the established thermal model. Under the consideration of contact impedance, this paper tests the heat production of the battery under high-frequency ripple current and establishes an accurate thermal model of a lithium-ion battery under the excitation of high-frequency ripple current, and the absolute value of the maximum relative error between the measurement results and the thermal model is reduced from 181.4% to less than 20.6%, which makes the battery thermal model under high-frequency ripple current excitation more accurate. Then, based on the established thermal model, the calculation method of the minimum heating power required for different batteries under the same low-temperature self-heating conditions is proposed for batteries of different sizes, thermal properties, and internal resistances, and the preferred low-temperature self-heating scheme for different types of batteries is proposed by comparing the current multiplicity required for different high-frequency ripple current self-heating schemes.

22 May 2026 in Electronics
Verified
Journal Article
Open access
PDF file
HLHao Li
Hao Li
Railway traction power supply systems (TPSSs) are evolving from passive grid-fed infrastructures into active energy systems with local photovoltaic (PV) generation capacity, energy storage systems (ESSs), and converter-based regulation. Unlike conventional microgrids, TPSSs feature single-phase, highly dynamic traction loads; short-duration regenerative braking bursts; and strict constraints on voltage quality, stability, and protection. These characteristics make the energy management of distributed PV-storage-integrated TPSSs a distinct research problem. This review examines the field from three coupled perspectives: supply architecture, power electronic interfaces, and energy management strategies. First, representative integration architectures are classified into substation-side, wayside-distributed, and hybrid multi-port schemes. Second, converter interfaces and flexible traction substations are analyzed as the enabling layer for coordinated control of PV, ESS, the utility grid, and traction feeders. Third, major energy management strategies, including rule-based, optimization-based, hierarchical multi-timescale, and uncertainty-aware methods, are compared. The review further discusses power quality, stability, protection, and battery degradation constraints that shape practical deployments. Finally, research gaps and future directions are identified to further the development of more robust, railway-specific, and implementation-oriented PV-storage energy management.

22 December 2025 in Batteries
Verified
Journal Article
Open access
PDF file
HLHao Li
Hao Li
This study presents a comparative analysis of the performance and modeling differences among lithium titanate oxide (LTO) batteries with three different cathode materials. An evaluation was conducted by performing performance tests over −20 °C to 25 °C at various current rates. Differences in open-circuit voltage curves, as well as charge and discharge capacities under different temperatures and C-rates, were systematically compared. At 25 °C, the NCM cathode enabled superior rate capability, retaining over 90% of its capacity at 8 C discharge, whereas the LCO-based cells exhibited significant capacity fade. Conversely, at −20 °C, the LCO cathode demonstrated better low-temperature performance, delivering almost 80% of its room-temperature capacity at 4 C, compared to less than 5% for the NCM cathode. The batteries were modeled using a second-order equivalent circuit model, and variations in model parameters were analyzed from the perspectives of internal resistance and electrode kinetics. The second-order equivalent circuit model revealed that the NCM-based cells had lower ohmic resistance and faster electrode kinetics. By correlating battery performance with cathode materials, this study evaluates the suitability of LTO batteries with different cathodes for various application scenarios, providing valuable insights for battery application and management.