This paper presents the use of TOPSIS, a multi-criteria decision-making model combined with the Taguchi method to find the optimum milling parameters. TOPSIS is the Technique for Order Preference by Similarity to the Ideal Solution and shows the value of closeness to the positive ideal solution. This study shows the optimum combination of process parameters using the shortest distance from the ideal solution. The surface roughness and flank tool wear were considered the objectives for simultaneous optimization. After converting multiple responses into a single response, the Taguchi method was used to analyze and determine the optimum machining parameters. According to reported studies, the initial wear behavior and initial cutting conditions have significant effects on the tool wear progress. Several initial cutting parameters can contribute to tool life and therefore can be used to improve both tool life and surface roughness. However, the cutting speed may significantly affect tool wear and ultimate tool life. In this study, an innovative solution was proposed for interrupted machining with two different cutting speeds. The first level cutting speed was used for 1 s and the second level was used for the rest of the process. The experimental results indicate that the initial speed followed by the feed rate significantly affects tool life. In addition, using the proposed strategy with different levels of cutting speed during machining operations led to improved tool life and surface roughness compared to conventional machining with uniform cutting speed throughout the entire process.

This work presents the first practical application of ionic electrolytes for electropolishing of nickel-based superalloys. It contains the results of an experiment-driven optimization of the applied potential and electrolyte temperature during electropolishing of laser powder bed-fused IN625 components containing surfaces oriented to the building platform under angles varying from 0 to 135°. For comparative purposes, the roughness profilometry and confocal microscopy techniques were used to characterize the surface finish topographies and the material removal rates of IN625 components subjected to electropolishing in ionic and acidic (reference) electrolytes. After 4 h of electropolishing in both electrolytes, a roughness of Ra ≤ 6.3 µm (ISO N9 grade number of roughness) was obtained for all the build orientations. To elaborate, both electrolytes manifested identical roughness evolutions with time on the 45° (75% Ra reduction) and 90°-oriented (65% Ra reduction) surfaces. Although the roughness reduction on the 135°-oriented surface in the ionic electrolyte was 17% less than in the acidic electrolyte, the former provided a more uniform roughness profile on the 0°-oriented surface (30% Ra reduction) and 44% higher current efficiency than the acidic electrolyte. This work proves that ionic electrolytes constitute a greener alternative to industrial acidic mixtures for electropolishing of three-dimensional (3D)-printed parts from nickel-based superalloys.

The microstructure and mechanical properties of IN625 alloy processed by laser powder bed fusion (LPBF) and then subjected to stress relief annealing, high temperature solution treatment, and hot isostatic pressing were studied. Tensile testing to failure was carried out in the 25–871 °C temperature range. Creep testing was conducted at 760 °C under 0.5–0.9 yield stress conditions. The results of the present study provided valuable insights into the static and creep properties of LPBF IN625 alloy, as compared to a wrought annealed alloy of similar composition. It was shown that at temperatures below 538 °C, the mechanical resistance and elongation to failure of the LPBF alloy were similar to those of its wrought counterpart, whereas at higher temperatures, the elongation to failure of the LPBF alloy became significantly lower than that of the wrought alloy. The solution-treated LPBF alloy exhibited significantly improved creep properties at 760 °C as compared to the wrought annealed alloy, especially under intermediate and low levels of stress.

This paper presents an experimental procedure developed to simulate the behavior of ceramic matrix composites (CMCs) under the cyclic thermal stresses of a gas turbine combustion chamber. An experimental apparatus was assembled that produces a temperature gradient across the thickness of a CMC specimen while holding the specimen at its two extremities, which simulates the bending stress that would be observed at the center of a combustor panel. Preliminary validation tests were performed in which A-N720 oxide–oxide CMC specimens were heated to a surface temperature of up to 1160 °C using an infrared heater, which allowed for the calibration of heat losses and material thermal conductivity. The specimen test conditions were compared with predicted conditions in generic annular combustor panels made of the same material. Provided that a more powerful heat source is made available to reach sufficiently high temperatures and through-thickness temperature gradients simultaneously, the proposed experiment promises to allow laboratory observation of representative deterioration modes of a CMC inside an actual combustion chamber.

Rapid tool wear and limited tool life are major problems when machining Inconel 718, which still need further attention. Amongst the reported strategies, limited studies have been reported on optimizing initial cutting conditions by means of tool life improvement. Therefore, in this work, the tool wear progress and tool life were investigated by varying the initial conditions in the transition period, which was set at four seconds. The transition point was discovered by previous works by the authors. After the transition point, similar cutting conditions were used as the reference condition. The tool wear morphology and size were recorded and analyzed in each condition. It was revealed that applying a lower cutting speed and feed rate in the transition period led to improved tool life as compared to the reference condition. In other words, the use of optimum levels of cutting parameters in the transition period of the cutting process may enhance tool life at higher cutting time. For instance, initial feed rate (0.15 mm/rev) and cutting speed (25 m/min) led to the improvement in the ultimate tool life by about 67% and 50%, respectively. Besides, applying the lower initial cutting speed, i.e., 25 m/min, increased the tool life by about 50% when the insert reached the maximum flank wear (v_Bmax) of 300 µm in comparison with those at higher initial cutting speeds. This phenomenon may lead to better insight into the effect of the influence of the initial cutting conditions in the transition period on tool life when machining hard-to-cut materials. Moreover, the built-up edge (BUE) was exhibited as the primary wear mode in all cutting conditions.